Question about Uniden BC72XLT Handheld Scanner

1 Answer

8 dig codes

This is my code 860.71250 how would i put it in my bank?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

Here is a manual on how to store the code. just go doun to page 33 and follow the dir.
http://www.uniden.com/pdf/BC72XLTom.pdf

Good luck

Posted on Dec 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you put the codes in?


yea that one is a little hard to operate....you want to put your frequencies into your private bank...what you do to program it is to go to your search mode hit program and then your search.and when you are searching and you find your frequencie that you want you put your scanner on hold this is manual mode. and push your private button and hit enter and your frequency is in there...and Barbara i will try to help you with this....

Jul 17, 2011 | Uniden BC350 Base Scanner

2 Answers

How do u unlock channels


hello You can unlock all locked out channels in any bank at one time. To do this, first press a bank key to start scanning. Then press [HOLD] to stop scanning. Press and hold down [L/O] ("L/O" appears on the screen) for more than 2.5 seconds until you hear the multi-beep ("L/O" disappears). Now all locked out channels in the bank are unlocked and restored for scanning hope this helps you cheers

Mar 16, 2011 | Uniden BC350C Base Scanner

1 Answer

Need to program codes in it!


You can't program the BC350C in the traditional manner -- you can only transfer displayed frequencies from the SCAN or SEARCH mode into the PRIVATE bank. This procedure is best described in the factory manual which you can download and print, at no cost, here:
http://www.uniden.com/pdf/BC92XLTom.pdf

For a comprehensive database of active frequencies in your area, visit:
www.RadioReference.com

Bill B.
Listening in since the 60's

Dec 09, 2010 | Uniden BC350C Base Scanner

2 Answers

How to program an Icom IC-R5 handheld scanner


to store a fcy press BAND to go to your fcy range ie 118.000 airband
dial your fcy ie 127.900(shanwick ocean area control) press and hold V/M for 1 sec, small numbers now blink, dial the memory slot you wish to store into ie 001 then press V/M again for 1sec and this will store 127.900 into mem slot 001. make a list:-
mem number / fcy / mode(am - fm) / station / bank
to prog a fcy into a "bank", press V/M for 1sec - blinking mem numbers - dial mem number ie 001(127.900) press MODE - "bank" flashes past-
-- -- -- -- 001 shows, turn dial to show A-00 this is the first "bank", pressing BAND scrolls through all the alpha "banks" - choose one.. ie A-00 (for airband..) press V/M this puts mem 001 into "bank" A mem slot 00, there are 100 slots in each letter 00 to 99. do this to any fcy you want to scan as a group.
to scan a bank press V/M - small numbers appear -
press BAND to scroll through any "banks" you have created ie A B C D etc (only banks with fcys in will display), press MODE -"bank"- press MODE again and you will start scanning just that "bank" of mem slots.
MODE starts and stops the scan... each letter holds 100 mem slots.. happy scanning!!!

Sep 22, 2009 | Icom IC-R5 Handheld Scanner

1 Answer

I have an Icom IC-R5 hand held reciever that needs to be programmed. How do I program this reciever? Please Help, Thank You in advance.


It is a bit long winded but, if you are familiar with how to store frequencies into memory numbers, it is almost the same for all the alpha numeric banks, then the rest of the programming is very similar to this method with the additions of tone, code, duplex up or down for each individual frequency etc. My advice is to write your own notes on a large sheet of paper and develop a chart with all your fcys in list order and where you have put them in banks, add how you got there and only refere to the manual if you get really stuck (the manual tends to be too vague and complicated to follow). if your scanner is empty at the moment, this is your best opportunity to learn the hard but best way to programme this lovely beast! ps the scanner is very good once you have mastered it...

Sep 22, 2009 | Icom IC-R5 Handheld Scanner

1 Answer

Can you recomend PC software for ICOM IC-R5 scanner


try this....
create an "airshow" bank to scan just the airshow fcys.
press V/M for 1sec -blinking mem numbers- dial a known mem that has an airshow fcy stored in it ie 025 (127.875) press MODE "bank" will flash past..
-- -- -- -- A-00 shows up ( I use this bank for airshows) press V/M, this puts mem 025 (127.875) into "bank" A mem slot 00, each letter holds 100 mem slots , put all your aishow fcys in here and when you scan bank A you will only scan the airshow fcys and not the entire airband!!
to scan a bank...
press V/M - small numbers show- press BAND this will diplay your bank letters, just select A## then press MODE for 1sec -"bank"- press MODE again and you will start scanning just A for airshows...
press MODE to start and stop the scan.. happy scanning! ps Southport was not as good this year as last year although it was good to see the vulcan again!!

Jun 08, 2009 | Icom IC-R5 Handheld Scanner

1 Answer

Radio Shack Pro-82 Scanner


when on the scanning part push the scan part again and push the prog buton that is under the lower arrow key and push it again so it will go to a different (blank channel) . you will know when it you are able to prog when the word prog will be on the bottom of the screen then go to cityfreq.com to find the codes for your area and put them in and then press enter. after you do that press the prog button again and it will move to the next number to program a different on when you get the desired amount of frequencies in your scanner just push scan and it will run through the entered codes.. Or if thats not the problem then on top should be a bank of numbers and andd you have to push the number of what bank you want it to run through at that time.

Jan 25, 2009 | Radio Shack Pro-82 Scanner

1 Answer

I have a new BC72XLT that I recieved as a gift. I have tried to program in the local frequencies but still have not been able to get one in. I have read the instruction book a hundred times. Can anyone me...


If you know the freq. codes, push hold, the bank number you want to store it in, push func., then push E(for program), type in the code(this includes the decimal), then push E. DLY will show up for a delay if there's not a transmission on the freq.

Jan 09, 2009 | Uniden BC72XLT Handheld Scanner

1 Answer

All channels locked out pro-2055


I hope this will help. It shows locking and unlocking ids while scanning and while in a bank.


Locking/Unlocking IDs Contents You can lock out IDs you don't want to hear such as telemetry, MDT's, dog catcher, etc. To Lock out an ID while scanning, quickly press L/OUT while the ID is displayed. To Lock or Unlock an ID manually: 1. In Manual mode select any channel of the bank you want to lock or unlock an ID in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the 1st line, the ID# in the list (0-29) on the 2nd line, the ID on the 3rd line, and bank tag on the 4th line (if programmed). 3. Press TRUNK (each time) to select the ID list (0-4). 4. Select the ID# (0-29) by pressing up.jpg or dn.jpg (or press and hold; faster) then press L/OUT to lock or unlock the ID. An L will appear to the right of the ID# if the ID is locked out. 5. Press MAN to exit programming. To Unlock IDs in a bank: 1. In Manual mode select any channel of the bank you want to view the locked out IDs in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list. 3. Press FUNC then L/OUT (each time) to view the locked IDs. Press L/OUT to unlock the ID. The next locked out ID will appear. 4. Press MAN to exit programming. Note: You cannot unlock all IDs at one time.

Nov 18, 2007 | Radio Shack Pro-2055 Base Scanner

Not finding what you are looking for?
Uniden BC72XLT Handheld Scanner Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Radio Scanners Experts

Iron
Iron

Level 3 Expert

3018 Answers

Robert McClure

Level 2 Expert

160 Answers

John
John

Level 2 Expert

473 Answers

Are you an Uniden Radio Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...