Question about Kwikset 907 907-15 Satin Nickel Powerbolt Keypad Electronic Deadbolt

1 Answer

Replaced batteries and door beeps all the time

There was a red light flashing from the back of the box so I replaced the batteries on the lock and now a green light flashes all the time and when i use the combination pad from the outside it unlocks the door but the box starts beeping!! It will beep every few seconds for about 1 minute...... i lost the set up instructions........ help help
thanks VICTOR
ps drink Mona Vie!!!!

Posted by on

  • Anonymous Feb 16, 2009

    I just changed new batteries I get green light and everything works,

    i can unlock it but it also beeps about four times for no reason.

  • Anonymous Mar 15, 2014

    I have no idea how to completely reset it. Batteries are good wondering if the circuits are fried or something


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

Here is the set up instructions.

Good Luck

Please rate FixYa!

Posted on Dec 18, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have just change the batterys on my sandleford electronic safe ES23. now I can not put my same code back in. can u help me please. it has a key n a key pad as well.

Open the safe, press the red button located inside the door, the yellow light will go on indicating the code can be changed. Input the new code, then press A or B button, it shall be confirmed by two beeps indicating the new code has been accepted and stored. If the yellow light and buzzer beeps 3 times the code is invalid - try again

Jun 27, 2016 | Locks & Locksmithing

1 Answer

Replaced batteries, now I am getting 3 sets of 2 loud beeps everytime I unlock the door with either code. Also the green light is continuously blinking.

The troubleshooting instructions (link here)

will tell you that you will get a series of quick beeps when the batteries are installed correctly and making good contact.Conversely, the low battery indicator light on the power board will be lit when the batteries need replacement. Kwikset recommends that you use four quality alkaline AA batteries.
Also, Kwikset recommends that if your Powerbolt is beeping, that you take out the batteries and remove the powerstrip. Let it sit for one minute, then put the batteries back in and wait for another minute. If it does not beep, as in above for battery replacement, then the keypad needs to be replaced. If the unit beeps, then the powerboard needs to be replaced.
Is it at all possible that, when you replaced the batteries, you did not get the orientation correct for one or more of the batteries? Did you use new, brand-name alkaline batteries?
So, I've taken you through the steps that a Customer Service Rep is going to ask you before you make a call. If the problem still persists, then it's time to make that call. The number is 800 327-5625, Mon.-Sat. between 7:30-4:00. Pacific coast time. They should be able to assist you further with troubleshooting and parts.

Good luck-and please provide feedback if this helps!

Dec 15, 2011 | Kwikset UltraMax Powerbolt 1000

1 Answer

Forgot the combination to the lock. Is there a way to retrieve the combination or return it to its factory default combination 1, 2, 3, 4, 5

The instructions below are copied from the programming instructions (page 11):

(The "out of box" factory default will be restored)
1. At the back of the lock, remove the screw at the bottom of
the lock housing and remove the cover.
2. Take out the battery pack and remove battery power by disconnecting
the battery pack.
3. Plug in the (provided) male shunt connector into the yellow
wire female connector.
4. With shunt connector connected, re-connect the battery
pack. The lock will immediately sound 3 short beeps (if
these 3 beeps are not heard, then restart at step 2).
5. The lock will then sound more slow beeps, 1 beep for every
second it takes to clear the memory.
6. After a few more seconds, the LED will slowly alternate between
flashing red and green--disconnect the yellow wire
shunt connector.
7. The LED will continue to slowly flash green and red for 25
seconds. To enroll Function Cards, proceed immediately
as follows:
• With the lock LED slowly alternating between flashing
red and green, present the Function Card #1
to the lock. The lock will sound 5 slow beeps.
• The lock LED will flash green rapidly. The lock is
ready to enroll the Function Cards.
• Re-present Function Card #1 to the lock. The
lock LED will flash green then red, with two beeps
(indicating the card was enrolled successfully).
• Present Function Card #2 to the lock. Again, the
lock LED will flash green then red, with two beeps.
• Continue to present, in order, Function Cards 3-
9. Each time a new Function Card is presented, the
lock LED will flash green then red, with two beeps.
After the 9th Function card is presented, the lock LED will flash
green twice, sound two beeps, and will then remain silent,
ready for use. Note: If the lock continues to beep after presenting
the 9th Function Card, check to verify that the yellow
wire shunt is disconnected.
Note: If you only wish to use the first 3 Function Cards, simply
allow the lock to "time out" after 30 seconds.

Here is the link to the complete instructions, in PDF form. You will need Adobe Acrobat or equivalent to view them:

Good luck-and please provide feedback if this helps!

Nov 04, 2011 | Trilogy ALARM LOCK PL3000 Series T3 Prox...

2 Answers

Does the green light flash all the time on my powerbolt and when I open the door from the outside there is a beeping sound this has never happened before not untill I changed the batterys.

Powerbolt is Beeping?

This is the relevant excerpt from the Powerbolt programming and troubleshooting instructions:

Why is my Powerbolt 1000 unit beeping?

To determine why your lock is beeping abnormally, please follow these steps:

Take out batteries and unplug powerstrip.
Let it sit for 1 minute, then put the batteries back in and wait another minute.
If it does not beep, the keypad needs to be replaced (17733-1).
If the unit continues to beep, the powerboard needs to be replaced (A17734-3,3 Powerboard 1470 brass finish; A17734-3,26D Powerboard 1470 satin chrome finish; A17734-3,5 Powerboard 1470 antique brass finish).

The complete page that I cut this from can be found by cutting and pasting this link into your browser search bar:

Since you've already gone through the battery change, this suggests that you need to replace the appropriate Powerboard for your lock.
So this is the link to Weiser Customer Support Page:

I suggest calling the appropriate toll-free number and having a conversation with a representative about this problem, first of all to confirm that you need the part before you go through the expense. Secondly, they will be able to get the correct part on order for you.

Good luck!

Jul 03, 2011 | Weiser Lock Powerbolt 1000 Lock

1 Answer

1) After unlocking door unit emits 2 beeps 4 times? 2) Green LED in door continually flashes?

remove all batteries, wait about 10 seconds then install new ones, one at a time, I found this clears the flashing

Mar 24, 2010 | Weiser Lock POWERBOLT ELEC DEADBOLT

2 Answers

My Adel Trinity 788 fails when read my (master) fingerprint (red light - two beeps). I already tryed to reset to factory defalts, pushing the 2 buttons (holding), removing a battery, then put the battery...

according to what he says:
if your lock does not recognize its master finger ud.hizo an attempt to reset and apparently not properly reset as initially ud. must press the two buttons at once not stop pushing, in followed remove a stack, reinstall again the battery immediately is oira one beep should expect from five to seven seconds is oira a different sound until that moment is reset your veneer and is at that very moment that are left of pressing the buttons.

then begins the process of adding tracks

Feb 22, 2010 | Trinity Keyless Biometric Fingerprint Door...

2 Answers

How do i know when to replace batteries ?

There's no sure way to know when to change the batteries. I'd suggest you change them at least once a year. Plan on it when you do your smoke alarm battery change, which should be done at least annually.

Jan 26, 2010 | Weiser Lock Powerbolt 1000 Lock

1 Answer

Have a SURESAFE brand safe at work which have no instructions

Hi there all I have a SURESAFE electronic security safe MODEL-OWSAFE30ES
(1) To set your own code first on safe
(2) locate the red reset button on the hinge end of the door.
(3) Press the red button, which will illuminate the yellow light on the keypad.
(4) Now key in your new code (3 to 8 digits) and press A or B to end. Note you have 30 second to complete this step.
(5) Test your new code whilst the door is open. Safe will beep twice to confirm code has been entered correctly, and knob can be turned clockwise.
(6) Repeat process any time you wish to change your code.,
Hope this help

Dec 30, 2009 | Safe International Digital Electronic Safe...

1 Answer

I installed my powerbolt today and it works but after i enter my code to unlock it, it retracts the bolt and then beats at me a couple times, but it works... and the green light keeps flashingwhats wrong...

Hello Lil Babe,

The lock is working just as it is supposed to. The beeping after it retracts is an audible signal to let you know that the lock has opened or closed.

The flashing green light is a visual signal to let you know that the lock is "open" and you are able to open the door. When the lock is "locked" the light will flash red momentarilly and then should stay solid red for a brief time.

Everything is working just fine, so congratulations on doing a successful installation of your new electronic lock!

I hope you find this Very Helpful and best regards!

Dec 11, 2009 | Weiser Lock Powerbolt 1000 Lock

2 Answers

Powerbolt 1000 started beeping and quit functioning

  • Take out batteries and unplug powerstrip.
  • Let it sit for 1 minute, then put the batteries back in and wait another minute.
I contacted customer support... they tell me the FAQ information on their own website is incorrect. The opposite is true, therefore the following is correct:
  • If it does not beep, the powerboard needs to be replaced
  • If the unit continues to beep, the keypad needs to be replaced
Here in Canada, they will send you a new one within 3-5 days free of charge. Call customer support:

Canada: 800-501-9471
US: 800-677-LOCK

The woman was very friendly. Great customer support!


Jun 14, 2009 | Weiser Lock Powerbolt 1000 Lock

Not finding what you are looking for?
Kwikset 907  907-15 Satin Nickel Powerbolt Keypad Electronic Deadbolt Logo

1,463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kwikset Locks & Locksmithing Experts


Level 3 Expert

3018 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers


Level 3 Expert

479 Answers

Are you a Kwikset Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides