Question about Vacuums

1 Answer

Kirby g4 belt replacement

How U do that? I see the ''belt on'' ''belt off'' signs. Cleaned out vacuum given to me by my Mom and don't know how to get the belt back on. HELP!>>

Posted by on

  • NeiN11 Dec 18, 2008

    Read domvac's solution and got it running. THX! domvac!!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Facing vacuum,turn belt lifter knob counterclockwise till it stops.Lift headlight hood,and unlatch brushead,and remove.Looking thru the hole in back,turn belt lifter knob clockwise to release belt.Remove bottom plate,and bend one end of bracket to remove end of brush roll.Slip new belt on and replace brushroll back into bracket,and replace bottom rug plate.Looking thru hole in back,turn belt lifter knob until the hook inside picks up belt.Replace brushead,and again,turn belt lifter knob clockwise to drop belt onto shaft.

Posted on Dec 18, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kirby G4 running very loud and smells hot.


were you put the belt on see if any thing is rubbing against shaft.it may have been the belt,replace the belt and clean out the bab and also the floor brush.

Jul 31, 2010 | Kirby G4 Bagged Upright Vacuum

1 Answer

How do you change the belt on a kirby g4 vacum


Greetings,

I have shot an excellent video repair on how to replace the belt on Kirby Generation Vacuum Cleaners, including your Generation 4, G4. The video is below in an easy to follow, and understand video. Feel free to use the pause controls to pause the movie as you're fixing the belt on your Kirby.




I hope this video was able to teach you the exact process of how the Kirby belt has to be installed in order for it to work properly. Please, if you have any questions just request a clarification of the repair and I'll be more then happy to help you further, I'm always happy to answer any questions. If you found this video helpful, please kindly rate this repair solution as helpful also. I really do appreciate it, thank you.

Thanks for watching!

Chris J.

Feb 20, 2010 | Kirby G4 Bagged Upright Vacuum

1 Answer

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,

Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;


Jan 30, 2010 | Kirby G4 Bagged Upright Vacuum

1 Answer

Kirby G4 causes black streaking when shampooing carpet


Replace the belt it is probably worn. You can get a replacement here:

Kirby G4 Belt

Dec 06, 2009 | Kirby G4 Bagged Upright Vacuum

2 Answers

Kirby g4 brush wont turn belt ok


your belt has probably been stretched to the point where it will not work so good.

Jul 02, 2009 | Kirby Ultimate G Bagged Upright Vacuum

3 Answers

Kirby heritage II


As long as it is Kirby belt - you should be fine. Make sure that the shaft is clean and that you do not vacuum something greasy or wet (grease or oil will lubricate the belt and shaft will loose the grip -heat up and burn). Make sure that brush roll spins freely.
I am assuming you know how to put the nozzle on properly (if you not sure - go here)

Good Luck
Rocky

Aug 22, 2008 | Kirby Heritage II Vacuum

1 Answer

Hello


here is a link to a site with detailed instructions on replacing the belt on your kirby

http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039

hope this helps!!!

Apr 06, 2008 | Kirby Ultimate G Bagged Upright Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...