Question about Pioneer DEH-P4300 CD Player

4 Answers

I CAN NOT FIND HOW TO HOOK UP THE SPEAKER WIRES ON MY DEH-P4300

Posted by on

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 233 Answers

The wires are as follows:

POWER:
(not all pioneers will have ALL the power wire colors, but they all will have red, yellow and black.)

blue - power antenna
blue/white - amplifier remote lead
orange - 12V+ from parking lights
yellow/black - unused
red - switched 12v+
yellow - constant 12v+
black - ground
SPEAKERS:
white/black - left front speaker (-)
white - left front speaker (+)
grey/black - right front speaker (-)
grey - right front speaker (+)
purple/black - right rear speaker (-)
purple - right rear speaker (+)
green/black - left rear speaker (-)
green - let rear speaker (+)

Posted on Dec 18, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

Here is a wire diagram for your radio. Cut and past in the browser bar.
http://www.pioneerelectronics.com/pio/pe/vgn/images/portal/cit_11221/49734CRD3311A_200012301332357300.pdf
Good Luck

Posted on Dec 18, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 916 Answers

You can get the installation manual here

http://www.pioneerelectronics.com/PUSA/Unassigned+Content/ci.DEH-P4300+Install+Manual.Protected

Posted on Dec 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bridging two12" subs and one 15" sub to my Rockford fosgate T 1500bd amp


assuming all 3 subs are 3-4 ohms, running all 3 in parallel (the 3 positive leads all attach to the amp positive terminal, and all 3 speaker negative leads connect to the amp negative terminal) will bring you at or above 1 ohm, which the amp is capable of handling. With 1500 watts, you will want to use 8 gague power leads for the amp, 12 gague speaker cables, and an inline 120 amp fuse between the amp and the battery, within 1 foot of the battery.

Jan 11, 2017 | Rockford Fosgate Car Audio & Video

2 Answers

Do you need to connect the yellow and red wires together if not used in a car on a pioneer DEH-X1950UB


Yellow - Connect to the constant 12 V supply terminal.
Red - Connect to terminal controlled by the ignition switch (12 V DC).

Jan 11, 2017 | Pioneer Car Audio & Video

1 Answer

Battery hook up----Does red go to + & blue to - ????


Car audio?

Google is your friend.

Google

make model installation instructions

They are all there online.

Google

Jan 09, 2017 | Car Audio & Video

1 Answer

So how do wire this set set up to a bridged amp any help would be appreciated


assuming that is a dvc dual 4 ohm speaker, and you have a 2 ohm bridged amp, you run a positive from each side of the speaker into the bridged positive of the power amp, and run a negative from each side of the speaker into the negative bridged terminal of the amp. if, indeed, you have 2 4 ohm voice coils, running them bridged in parallel wiring will bring the load to 2 ohms. if you have 4 voice coils, of 4 ohms apiece, you could run all 4 parallel into the amp, but that would bring the load down to 1 ohm, and you would have to make sure you8r amp can support 1 ohm operation.

Jan 07, 2017 | Car Audio & Video

1 Answer

I have a boss 400w riot 2-4 channels,how do i connect the high level wires? Because stereo doesn't have rca's


to use the high level leads, you have to isolate the wires going to each speaker (if using 4 channel mode) or isolate the wires going just to the rear if you are using 2 channel mode. you have to strip a small piece of the insulation off each speaker wire, and run it into the amps high level input harness. if you dont have the high level input harness, you can get a 2 channel high level to rca adapter for around $20. basically, you are tapping into the signal to the stock speakers to feed music to the amp. make sure you get all your positives and negatives correct. brighter wires are usually positive; however you may be faced with sa speaker which uses a grey wire, and another grey wire- the second with a black line. you will have to, again, turn to internet research to determine which is positive and negative, if the colors are not obvious.

Dec 30, 2016 | Boss Car Audio & Video

1 Answer

1992 GOLDWING RADIO SPEAKERS NOT WORKING


All you can do is trace the wiring back from the radio to the speakers, there is no quick fix here. To test the speakers touch a battery to the two contacts, the speaker will pop if it is any good.

Nov 06, 2012 | Car Audio & Video

3 Answers

Lightning audio b150.2 as soon as +12 is hooked up blows 25 amp fuse and the c2 1000uf/35v capacitors blow???????


Disconnect all speaker connections and rca cables. Leave power, ground and remote wires intact. Try turning on again. If you still have a protection light your amp is faulty. Hopefully you have warranty. Double check all connections .A thumbs up would be greatly appreciated if this answer is helpful to you.

Aug 25, 2009 | Lightning Audio PC2 Capacitor Car Audio...

2 Answers

RCA CABLES


RCA cables are the best way to get the audio from your head unit to the amp. If your head unit doesn't have RCA outputs, you might be able to use the speaker outputs of the head unit to connect to the "high power" or "high level" inputs of the amp, if the amp has such inputs (check your manual).

Mar 23, 2008 | Lightning Audio LA1.300.2 Car Audio...

Not finding what you are looking for?
Pioneer DEH-P4300 CD Player Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

Michael Kovalik III
Michael Kovalik III

Level 2 Expert

117 Answers

The Knight
The Knight

Level 3 Expert

71754 Answers

yadayada
yadayada

Level 3 Expert

68038 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...