Question about Akai LCT2060 Television

1 Answer

Akai lct2060 fell 8 inches to floor,wont power on

Ribbon cable from lcd screen to rear mother board came apart when it fell. Can I take the tv totally apart so I can re plug the power ribbon?

Posted by on

  • Anonymous May 15, 2009

    I have a LCT2785TA LCD TV AKAI model and the ribbon was punctured do you know where I could find a replacement part? I just need one.



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The ribbon can be replaced but be careful and use gloves to avoid contaminating the componite with the oils from your hands

Posted on Dec 25, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What can I do to repair a vertical stripe on my LED TV??

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience.
Line, faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. Line faults to all LCD screen are similar, irrespective of its brand and screen size.

Jan 25, 2016 | Televison & Video

1 Answer

Broken LCD screen

your answer to this problem is easy. First take the batteries out of the camera, then open the camera ( screws should be in the back) the screen should just pop out of the cover and there is a ribbon cable that connects the screen to the circut board. Gently un-hook that ribbon where it plugs in to the board there might be a slid lock to hold the ribbon in place, it should unlock when you pull the cable out (memorize what position the ribbon is before unplugging). Now the fun part, do the same thing to the other camera, (carefully). To install the new screen, plug the ribbon back into the slot and it should be snug, if not there is a lock on it, gently push it back away from the ribbon ( a little finger pressure). Now, simply put it back together the same exact way you took it apart and don't forget the batteries. Have fun taking pictures...

Btw, I’m available to help over the phone in case u need at

Nov 01, 2007 | Olympus SP-350 Digital Camera

1 Answer

I have a lcd toshiba mod 52xv545u the left side is dark it reset it self

Looks like a Tconn problem caused by
1 Main Power supply inside unit
2 Tconn board itself, or ribbon cable connections
3 panel, or ribbon cable connections from Tconn to panel(screen)

Feb 02, 2015 | Toshiba 52XV540U 52 in. HDTV LCD TV

2 Answers

I have a Lg 42" lcd tv (42LG3000) TV is wall

White screen with good audio. before buying pcbs & such. try my repair method.. you need to get the lcd unit off the facia & then remove the front lcd metal frame. at the top of the screen you have 2 thin pcbs - chances are that the ribbon cable got at least one track unbonded. first off put some double sided tape under the pcbs to stick then to the frame - that'll take the bend out of those pcbs !! next put cellotape over the ribbon cables. i then cut 6 pieces of sponge 15mm thick & wide as the ribbon cable & glue to the tape on the ribbon at what would be the top edge of the screen (covering the point where ribbon meets pcb).. put the metal frame on top edge first to keep the sponge straight !! put it back together & fire it up. if it still aint working you may need a tcon pcb (little square one at the top). this fixed my 42lg3000 but can work on others with same fault !!

Mar 16, 2011 | LG 42LC2D 42 in. LCD HDTV

2 Answers

I hv changed and replaced all three , the mother board, draffon board and power supply board in my KLV32U100m since it went off from the protection system. now the power gets on but no picture ( cannot...

I would check the ribbon cable that connects the LCD remove from connector and reconnect. The connector, ribbon cable or the points it connects to the LCD panel itself could be bad. The only way to really be sure is to install the LCD panel in a working TV and see if it works.
I have purchased TV's with cracked screens (that powered on) ebay fairly cheap for this purpose a couple time's and it has worked out well.

Sep 14, 2010 | Sony BRAVIA KLV-32U100M 32 in. LCD...

1 Answer

The display of my dualphone 3088 is blue can I do an hard resert

The Dualphone 3088 LCD screen has a terrible habit of coming loose from the ribbon connector socket on the main board. If you take the phone apart, carefully remove the LCD screen from the plastic surround it is in and you will see the ribbon and its board connector. The phone will have a black screen if the connector has come out completely or at least the power pins are out or you will get wierd colors, loss of colors etc if the cable is partially disconnected.

The small clips on either side of the connector have a habit of coming loose, freeing the LCD screen. Carefully put the ribbon cable from the LCD screen back into the connector, you will need to press both clips on the connector at the same time to lock it in place. (yes its fiddly and I have to do it all the damn time)

Jun 10, 2010 | RTX DUALphone 3088

1 Answer

My tv will not turn on but making a click noise only

something is pulling down the power suppy and not letting it come up. if you feel confident and know electrical safety, remove the back panel and find the furthest ribbon cable inside going to the board on the left. there are 3 boards at the bottom of the tv, the one on the left is a mother board with many daugher boards plugged into it and standing up. there are 3 ribbon cables that send power from the middle board to the left board. the back most one (front of tv) the one furthest in, under the tubes, is the convergence power. usually if you pull this cable and then plug it in, it will come on and the picuture will be all bowed and distorted. this is a shorted convergence chip, usually a stk392-120
replace both of them and any burnt up resistors to solve your problem
this is a tricky repair, let me know if you need further assistance
typical cost is 150 to 350 $

May 21, 2010 | Philips 51PP9910 51" Rear Projection HDTV

2 Answers

How do I change the LCD screen please?

Very easy.
Remove the batery. Remove the case screws and pull the case apart. Where the flat ribbon cables connect to the main board, carefully release the clamps on the board end plugs. The plugs don't come off, the ribbon just comes out of them. Carefully remove the screen. It has double stick foam in a few spots. Put the new screen in, reconnect the ribbon cables and put the case back together. 30 minutes max.

Sep 30, 2009 | Canon PowerShot SD400 / IXUS 50 Digital...

2 Answers

Acer aspire L100

It helps to know what to ask for....

Is it the ribbon cable (see below)
9fc9b24.gif Or the 4 pin molex plug? (see below)
9b76c9f.jpg Or a SATA cable? (see below)
8de40ec.gif Or an eSATA cable (see below)
c71f854.jpg Or the sata Power cable? (see below)
Then you can go on the internet and find and purchase the right cable you need replaced.

Jul 03, 2008 | Acer Aspire L100 PC Desktop

Not finding what you are looking for?
Akai LCT2060 Television Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Akai Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2336 Answers

The Knight
The Knight

Level 3 Expert

75767 Answers


Level 3 Expert

81400 Answers

Are you an Akai Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides