Question about Sennheiser Evolution G2 100 Series UHF Handheld Microphone System (A) EW135PG2A Microphone

1 Answer

All four hand held systems failed

We have 4 handheld and 4 lapels of the g2 100 range, in the rack they are set up with two splitters but per splitter we have only 2 hand helds and 2 lapels.

in a performance all 4 of the handhelds stopped working, but all of the lapels continued to work.

both the transmitter and reciever were un-muted, the reciever said they were un-muted but wasn't recieving signal. normally when they are not recieving they say on the reciever they are muted aswell. so they must have been recieving something or they would appear to be mute

we collected all of the handhelds in the middle of the performance and took them off stage to test them. they didnt work for 2 or 3 minutes and then they all came back on again. nobody toutched the recievers and i was the only one speaking into all 4 mics when they suddenly came on all at the same time. the total down time was about 5 mins.

This is really bizzare and has never happened in the 3 years we have had them

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 110 Answers

Check out override frecq see if you can change transmit and recieve switch settings ie dip switch sets sombodys overiding your freks

Posted on Apr 24, 2010

2 Suggested Answers

robotek
  • 1512 Answers

SOURCE: all four hand held systems failed during a performance

Hi kb

That is an odd encounter, and most probably one of the R.F.I. kind. Radio Frequency Inference can be caused by many things. Sometimes it can be a nearby piece of equipment creating that much interference, that the mics could not operate. It may have been a spurious mobile radio transmitter as used with two way radio for the cops, ambo's, firies,or even a nearby Cab!! Some times faulty light dimmers can also spray RF.
To what ever end, the fact that 4 mics went down together is indicative of an external problem, and being radio mics, it would have been radio interference.
The only other thing to check is that they are UHF. there are many VHF mic systems still about, but these frequencies are now being used as part of the soon to be introduced digital TV transmission. Best check that they are UHF, The VHF type have actually been illegal for a number of years Hope this info has helped you understand your problem. I am happy to answer any questions you may have. Cheers

regards
robotek

Posted on Dec 17, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

THE SYSTEM IS CONNECTED DIRECTLY INTO THE RECEIVER THAN INTO THE MONITOR. AS FAR AS I KNOW IT IS NOT CONNECTED TO MY INTERNET.


one thing that you can do is turn on the auto login feature if the screen goes blank or the login session times out. I am not aware of any reason why the system would time out. The auto login setting will log you in in the event your screen goes blank.

Jan 08, 2017 | The Audio Players & Recorders

1 Answer

What r the codes for ge universal remote for kirsh home theater system model k3


Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
Programming Notes
• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.
Search the site by type in the "brand name" to your device; to which you want set-up codes; in the "Search box at the top right of the display window" to get gathered related posts.

Jan 08, 2017 | GE Audio Players & Recorders

1 Answer

Want to use my current speakers with a new surround sound system. Current system is 5.1 channels, rated at 100w per channel @ 8. Ohms. New System is rated 145watts, 5.2 channels at 6 Ohms. Will b ok?


Hi Ronald.
8 Ohm speakers will work just fine as replacements for the
6 ohm speakers. When fitting speakers you need to consider
The power handling capability. The impedance and the frequencies
involved. Power handling is expressed in wattage ie 100W.
Unfortunately this can be expressed in rms, max or peak music. The rms value (root mean square) is the only really relevant figure as this is the continuose handling power at 1 KHz. The impedance
is the resistance that the amp sees but is not a dc resistance and
varies with frequency. The lower the impedance the more power
will be drawn from the amp. In the event of a short circuit across
the speaker the amp will try to deliver infinite power into an infinitly
small load in an infinitesimal amount of time and will self destruct.
Using an 8 Ohm speaker draws less power than a 6 Ohm speaker.
Connecting speakers in parallel; results in the impedance beingreduced. For example two 8 Ohm speakers in parallel will result
in a 4 Ohm impedance load but in series will be 16 Ohms.
Incidentally the the .1 (5.1) is the sub woofer which only has
to handle the bass frequencies, a small percentage of the
amplifiers overall frequency response..
Connect your speakers and then power up the amp last
after double checking there are no shorts on the speaker
cables.
All the very best from Vintie.





Jan 07, 2017 | Audio Players & Recorders

1 Answer

Kenwood VR-357 Audio Video Surround Receiver manuals


Try Googling (kenwood)(VR-357)(manual) without parens.

Jan 02, 2017 | Kenwood VR-357

1 Answer

How do I remove the speaker that is held in place by plastic circle that has been melted in certain spots over the edge of the speaker.


You can just use some snippers carefully then when you replace it either use gorilla or a glue gun.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Feb 06, 2016 | Audio Players & Recorders

1 Answer

How do I test for a poor ground wire as opposed to a bad ground wire?


One tiny wire has very little resistance. Turn up your Ohm meter to it's highest setting. Be sure to have it calibrated exactly the same for each test (zeroed out). The very good connection should read infinite but the tiny connection should show a tiny bit of resistance. It's difficult but not impossible. Get a friend to help so the resistance in your body doesn't affect the data. Use one hand and new clips.

Jan 23, 2015 | Audio Players & Recorders

2 Answers

Hi,Just purchased 2 antec gain Bluetooth receivers type bxr 100. Operating instructions are not included. Maybe it's just me, but i'm not succeeding in getting them to work. No lights at all when they


Make sure that the unit is fully charged by a micro USB the light on it will be red until it's fully charged put phone in search mode and press the center button until the light flashes red and blue after the phone finds it you should have an option to auto pair when it's not in use it will turn off when paired and working pressing either track button will start the music player then just play with the buttons and see what it does you can stop anything from the phone controls

Mar 18, 2014 | Antec BXR-100 Gry Audio...

2 Answers

Iwave pod bluetooth speaker


Unless your PC is Bluetooth capable, you'll need to get a Bluetooth device to make it so. This is just one of many such devices to select from. Amazon com Roker Ultra Mini CSR Bluetooth 4 0 Usb Adator for PC and... They vary in size and price. Shop around to find one that best suits your budget. But you want an adaptor/receiver specifically for Bluetooth. (you will need an empty USB port for the adaptor)

Hope this information helps, best of luck!

Feb 06, 2014 | Audio Players & Recorders

2 Answers

Can't get my computer to discover my s9 headphones. There are no other BT devices connected. The blue light is on...


What bluetooth adapter are you using on your computer? Get the manual for the S9 from the Motorola web site: it will tell you that the blue light is related to mono voice/microphone, and flashing green is all about stereo musioc, no microphone. 
So what are you trying to do with your S9?
On your computer it can be hands-free, or a stereo headset. It has two personalities, and you should see the two modes in your bluetooth configuration screen on the PC.
From what I see in the Motorola manual, if you click the right ear button for "Play/pause" it is supposed to kick the headset into A2DP stereo playback. 

Mar 04, 2009 | Motorola Mobility S9 Headphones

5 Answers

BOSe Wave Radio - Disk "not readable"


I had the same problem with the disk unreadable error and took my unit to a authorized repair dealer about 100 miles from where I live to have it fixed. It ended up costing me about $300 to have the CD unit totally replaced which is almost as much as I paid for the unit in the first place. I am like a lot of you that used the CD very little although the unit was about 3 years old. I think Bose has a problem and would like us to think it is very rare. I bought a Lifestyle surround system about 14 years ago that has a CD and have never had a problem with it so needless to say I am very disappointed in the Wave II Radio/CD system. I am fairly certain the problem will occur again, but only time will tell.

Mar 03, 2008 | Bose Wave Radio

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sennheiser Audio Players & Recorders Experts

Rick

Level 2 Expert

611 Answers

Geoff

Level 3 Expert

413 Answers

Brad Brown

Level 3 Expert

13732 Answers

Are you a Sennheiser Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...