Question about Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

3 Answers

Whirlpool clean light flashes 7 times

Whirlpool model GU2500XTPQ6 has the clean led flashing 7 times and will not run. Is there something that I can check before calling out the expensive repair man? Unit is 18 months old. Thanks Scott

Posted by on

  • 4 more comments 
  • semushlich Nov 12, 2007

    We have the same problem. The one solution suggested here did not work so we're still looking for help...

  • Donnabelle Feb 21, 2008

    Same problem and will now not start up again? I had just used the Glass Xpress option and then this problem began?



    Thanks,

    Donna

  • Anonymous Jul 29, 2008

    Same Problem after 7 days away on vacation!! Clean light blinks 7 times. Using the key sequence below cleared the error and allowed normal wash cycles to resume. Hope the problem does not come back. This unit is about 3.5 years Old and has never had another problem. Why doesn't the troubleshouting section of the manual simply say to do this ? Instead it says you have to call for service!!

    Thanks Eric.

  • Anonymous Mar 04, 2009

    Toby,



    Thanks I used the procedure and it worked for me.

  • dcfrank1 Apr 04, 2009

    I have the same blinking clean light problem and am running the diagnostic now using the HEATED DRY, NORMAL, HEATED DRY, NORMAL mentioned above.

    Will this yield an error code and if so, where can I find what it means?

  • Anonymous Apr 21, 2009

    I have the 7 time blinking clean light problem. After entering the code to clear I saw a d1 code. The washer started working again but I dont know if the problem will reoccure. What does the code mean? Will the problem return on the first run cycle?



×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Actually, the button order to put it in a diagnostic cycle and clear the blinking clean light on the gu2500 is HEATED DRY, NORMAL, HEATED DRY, NORMAL not the other way around as Iden had posted.

Posted on Jun 15, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

We have the same problem, I found this on the net. press normal, heat dry, normal, heat dry. This will run it through a cycle and stop the light. It still is doing it on a regular basis, but at least I can clear it and keep using it.

Posted on Sep 29, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The problem the first time this happened was that the control panel was fried and needed to be replaced. The second time this happened (yup, twice!) was that the switches when the door closed were not connecting properly and both had to be replaced.

Posted on Jun 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No sign of life to our 5 year old D/W except flashing "CLEAN" L.E.D.


7-1 heating circuit problem control programmed to shut down machine when no rise in water temp during heat cycle, you either have an open heating element or wire burnt a shorted thermistor or a bad control not outputing 120VAC to the heater you can reset the control by placing the machine into diagnostic hit cancel button to turn off all the lights press heated dry-normal, heated dry- normal within 6 seconds lights should come on press cancel unit should start it will run till same part of cycle reached and lock out again if it has not been removed the little black panel below the door remove should have the tech sheet in a plastic pouch which explains how to check the components mentioned earlier,

Apr 03, 2014 | Whirlpool GU2800XTV Dishwasher

2 Answers

Whirlpool dishwasher model Gu2548XTPS7, clean light flashes 7 times and won't start.


Check, if you have water in the machine, if yes, your control board could at fault

Mar 20, 2013 | Dishwashers

1 Answer

Whirlpool Quiet Partner II clean light blinks 7 times


The clean light flashing 7 times is an error code indicating an issue with the wash temperature. If the control does not detect a 4*F temperature rise in the main wash cycle, it will display the fault as the clean light flashing 7 times. There are several things that could cause the water not to heat, including the water being too hot coming in, an open door switch, or a faulty component in the heater circuit. The most common cause is the door switch not closing properly. This can be due to a loading issue or a latch issue. If upon visual inspection of the heating element no obvious defects are found, I would recommend resetting the control and running another cycle, paying close attention to door closure. If the light begins flashing again, you likely have a component failure. The heat circuit consists of several components including the element, control, door switch and tub thermostat(s). Reset the control by pressing teh following buttons within 5 seconds.

Hit Temp Wash Heated Dry Hi Temp Wash Heated Dry
.

Mar 02, 2012 | Whirlpool Dishwashers

1 Answer

The panel is stuck on pots/pans for cleaning and wont let me run the dishwasher. the pots/pans light keeps flashing


Hello,

To reset the dishwasher push in this order the,

HIGH TEMP WASH- HEATED DRY- HIGH TEMP WASH- HEATED DRY - CANCEL/OFF

the control will be reset...but more importantly how many times in a row does the light flash..it will indicate what error code its displaying??

example if it flashes 4 times then a pause then flashes 4 times again its displaying the error code#4
7 flashes then pause then 7 flashes its displaying the error code#7 ect ect



GENE

Sep 06, 2011 | Whirlpool 24 in. DU1055XTPS Stainless...

1 Answer

My Whirlpool DU1145XTP won't turn on. Clean light


Check the themistor in the control panel. Radio Shack sells these for about $1.30 each. I replaced the one in my dishwasher three years ago and have had no issues since.

May 16, 2010 | Whirlpool 24 in. DU1100XTP Built-in...

1 Answer

Clean light flashing 7 times.


Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.
If the clean light is the one flashing then your dishawasher could have a heater circuit problem (depending on the age) or this could simply just be water colder than it is used to getting.
Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has untill all the LED lights come on, press cancel twice and try the dishwasher again making sure to run the water at the kitchen sink till it is hot before starting the dishwasher, if this trips and locks you have a problem with the heating element, or temp sensor.
Press the heated dry button followed by the normal cycle button, and then repeat once. You should see all of the lights come on for a second or two, and then the dishwasher will work again.
If you haven't already, take a look under the kick plate in front to see if there is a schematic tucked in there somewhere. Whirlpool has put their diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.
HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!

Jan 06, 2010 | Whirlpool Dishwashers

1 Answer

Our clean light flashes 7 times pauses and flashes 7 times again, we can not restart the unit whats could be wrong


Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.If the clean light is the one flashing then your dishwasher could have a heater circuit problem (depending on the age) or this could simply just be water colder than it is used to getting.

Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has until all the LED lights come on, press cancel twice and try the dishwasher again making sure to run the water at the kitchen sink till it is hot before starting the dishwasher, if this trips and locks you have a problem with the heating element, or temp sensor.
Press the heated dry button followed by the normal cycle button, and then repeat once. You should see all of the lights come on for a second or two, and then the dishwasher will work again.

If you haven't already, take a look under the kick plate in front to see if there is a schematic tucked in there somewhere. Whirlpool has put their diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.

HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!




Dec 30, 2009 | Whirlpool Dishwashers

1 Answer

Clean light flashes 7 times at a time.


Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.
If the clean light is the one flashing then your dishawasher could have a heater circuit problem (depending on the age) or this could simply just be water colder than it is used to getting.
Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has untill all the LED lights come on, press cancel twice and try the dishwasher again making sure to run the water at the kitchen sink till it is hot before starting the dishwasher, if this trips and locks you have a problem with the heating element, or temp sensor.
Press the heated dry button followed by the normal cycle button, and then repeat once. You should see all of the lights come on for a second or two, and then the dishwasher will work again.
If you haven't already, take a look under the kick plate in front to see if there is a schematic tucked in there somewhere. Whirlpool has put their diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.
HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!


Oct 07, 2009 | Kenmore Dishwashers

2 Answers

I have a whirlpool dishwasher (gu2500xtpq6) wont fill up


water level should be approx 1/4--1/2 inch below the heating coil.. this is normal fill level

Apr 28, 2009 | Whirlpool 24 in. GU2500 XTP Built-in...

1 Answer

Clean light flashes


You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 11, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Whirlpool 24 in. GU2500 XTP Built-in Dishwasher Logo

2,373 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Mike

Level 3 Expert

4354 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...