Question about Ricoh Aficio 1035 Copier

1 Answer

Ricoh Aficio 2027, Service Code 320

Hi, When I turn the machine on it tells me "Functional Problem within the copier. Turn operation switch off then on. If the error appears again, call service. SC320.
I have turned the machine off and on, unplugged it and still get the same message. Please help.

Posted by on

  • misrael Dec 17, 2008

    Thanks, it cleared for a few seconds but then came back. How expensive is a new laser motor? Is it something I can install or must I call a pro?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ricoh Master
  • 990 Answers

Dear sir; the error code 320 on ricoh af 2027 it's means laser polygon motor problem, the laser unit right under the toner unit, litlle bit left. some error code can be reset why don't give them a try
1, power on the machine
2, press "clear mode"( has the c in a diamond), "107"then press and hold down "clear/stop" key
3,turn power off 10 second later back on.
I f reset doesn't work, you need to replace laser motor. thank you
HAVE A HAPPY HOLIDAY

Posted on Dec 17, 2008

  • Everett Lin Dec 18, 2008

    The motor price I'm not sure, but by my experience the price around $ 70.00 us dollar, If you are handy man why don't try it.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ricoh Aficio MPC 2500 error SC 442


image transfer belt contact sensor is dirty clean it

Feb 17, 2014 | Ricoh Printers & Copiers

1 Answer

Functional problem


change the td sensor below the developer unit or if possibly change the complete developer unit

Jan 02, 2014 | Ricoh Aficio 1035 Copier

1 Answer

MY GESTETNER 3218 AFICIO FUNCTIONAL PROBLEM SC 320. HOW CAN I SOLVE THE PROBLEM


SC 320 - Polygon motor error.
The polygon motor does not reach its operating speed within 10 sec. after the polygon motor on signal,or the lock signal is not detected for more than 40 ms continuosly during operation.
Possible causes polygon motor defective,poor conection of the interface harness which connects the polygon motor driver and the IOCSS board, IOCSS bboard defective.
The SC can be reset by turning the main switch OFF and ON if the SC was caused by a sensor error.
To reset SC press yellow key 1 - 0 - 7 and STOP ( red ) key for 3 seconds,enter in the SP mode, enter SP 5-810 ( SC code reset) and select "1".Then hold down the Photo mode key and the # key at the same time for at least 3 seconds(this does not require the main switch to be turned off and on).

Aug 22, 2012 | Ricoh Aficio 250 Copier

1 Answer

I have a ricoh 2051 with this error message: Functional problem within the machine. Turn main power switch off and then on. if the error appears again, then call Here is the error message code: SC...


After turn the main switch off and on the error appears again????
This error means that there is a bad comunication between the controller board and the operation panel.
Did you intervew in the machine? Some tecnical intervewing?

Feb 17, 2011 | Ricoh Aficio 1035 Copier

1 Answer

What is error code SC548 on RICOH Aficio 2035/2045 machine. Functional problem within the copier. How do i reset the copier to operate normal?


SC548 means the machine it not seeing the fuser unit. Open the Right side and front doors. Check the fuser unit to see if it is mounted properly.
There is some connection on the fuser module not making good contact. Reseat the fuser and power the machine off and on.
If you need to reset. Press Clear all, 107 and hold the pink button until you cee copy sp page displayed. Press copy sp, then while on that page turn the machine off and back on.

Jul 19, 2010 | Ricoh Aficio 2035 Copier

1 Answer

I Cannot solve SC541 Error in RICOH Aficio 270


It's not the PCU (photoCONDUCTOR unit), It's either a thermistor or blown out heater lamp in the fuser. Call a tech. The code can only be reset in service mode

Jun 23, 2010 | Ricoh Aficio 2027 All-In-One Laser Printer

1 Answer

I turn on my ricoh aficio 2027 this code SC670 APPEAR


670 D Engine response error After powering on the machine, a response is not received from the engine within 30 seconds. • SBCU installed incorrectly • SBCU defective • Controller board defective
You can try to reseat the connectors on those 2 boards, if that doesnt work you may need to replace those boards.

Mar 15, 2010 | Ricoh Aficio 1035 Copier

2 Answers

Ricoh aficio 2027


SC542 is a warm up error from the fuser.

SC 870 is an address book error.

Turn the power off on the copier. Wait 30 seconds and then turn the power back on. See if it goes away.

Let me know if it doesn't.

Jul 12, 2008 | Ricoh Aficio 2027 All-In-One Laser Printer

1 Answer

Ricoh Aficio 1018 photocopier


For the Aficio 1018. SC-320 is laser failure - the polygon mirror motor inside the laser has failed and needs replacing. You will need to contact your nearest service agent for repair.

For your RICOH Aficio 1013F - SC-551 is overheat in standby mode as far as I can tell. The circuitry that controls the fuser section ie manages the heat has problem. Unless its right near a source of heat like a heater or has no circulation around you machine you will need contact a repair agent for this machine also.

Mar 18, 2008 | Ricoh Aficio 1013F Copier

Not finding what you are looking for?
Ricoh Aficio 1035 Copier Logo

1,487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Printers & Copiers Experts

quennie732

Level 2 Expert

393 Answers

Bernard D'Souza

Level 2 Expert

161 Answers

OfficeServiceAjnc
OfficeServiceAjnc

Level 2 Expert

181 Answers

Are you a Ricoh Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...