Question about Kenmore 22422 Top Load Washer

2 Answers

Alll the water does not spin out , clothes still wet

No matter the size of the load, but mostly occurs with heavier loads, the spin cycle doesn't seem to reach full speed so not all the water is spun out. Clothes are still wet after cycle, and need to be re spun 2 or 3 times.

Posted by on

  • zbicka Dec 17, 2008

    Is a clutch difficult to replace? Do you think I could do it, I've replaced dryer drum liner before?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 161 Answers

If there is no standing water then the pump is doing it's job but, if the spin is too slow then it sounds like the motor is the problem.

The motor will eventually stop during the spin and after cooling off for a while will work again. The motor will need to be replaced.

Posted on Dec 17, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 113 Answers

Your clutch is wearing out and needs to be replaced. It will only get worse. Ive included a schematic , part # is 285785. #5 on the schematic. Let me know if you need more help, thanks dave www.washermd.com

alll the water does not spin out , clothes still w - 0105782.png

Posted on Dec 17, 2008

  • Dave Dec 17, 2008

    No its not too tough I can walk you thorugh it. Gonna take some time though. I can do it in 15 minutes, only cause ive done it a million and one times. Best way would be to enter a private chat though. Cause your gonna need step by step. Let me know , thanks

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washing Machine Won't Spin Dry Clothes


You may be overloading the machine. Just because you got them all in there and wet, doesn't mean there was enough room for them to get a good washing. Cut back on size of the load (make sure you have large load selected) and see if that doesn't help you.

Jan 22, 2014 | Kenmore 44932 Front Load Washer

1 Answer

Clothes too damp after spin cycle


Front loading washers are notorious for not spinning the water out of a small load of clothes. This is because there is not enough clothes in the washer to balance the tub during the spin cycle.

Try washing a slightly larger load with a minimum of six items or more. This is one of the downsides to front load models and no specific brand is immune to the problem.

Mar 17, 2013 | Washing Machines

1 Answer

Washer will not spin at all no code . will drain and tumble back and forth,when it comes time to spin it turns off.


A washing machine is basically a big tub that repeatedly fills with water and then drains, spins to wring clothes dry, and has a device for stirring things up-- either an agitator in the middle of a top-load machine or a rolling drum in the case of a front-loader.
The four cycles that every washer performs are fill, wash, drain, and spin. Though these functions are pretty basic, a number of things can go wrong with them.
There are a number of problems that you can fix quite simply; some issues, however, are better left in the hands of an appliance repairperson.Problems that commonly occur with a clothes washer are discussed in depth below.If your washer doesn't run, be sure it's plugged in and that the receptacle works (the circuit hasn't overloaded). Before working on the washing machine, be sure to unplug it.
To prevent problems, follow good maintenance procedures. Use the right amount of detergent for your washer and your water hardness, make sure the machine is level, and don't overload it for the cycle chosen.

Washing Machine Does Not Fill
If the washer doesn't fill, the water inlet screens may be blocked. Clean or replace them. (Check your owner's manual for the location of the screens; they're often located at one end of the supply hoses, or you may have to remove a panel to access them.) Other reasons for not filling may be that either the timer or temperature selector is broken--both of these are repairs for an appliance repairperson.

Washer Does Not Spin
If your washer doesn't spin, check to see if the clothes have jammed or are unbalanced in the drum before calling a repairperson. Unbalanced clothes will also cause a w
asher to shudder or "walk." If straightening out the load doesn't stop the washer from shaking, look at the feet underneath and be sure they are properly adjusted to keep the washer sitting level on the floor (you just turn them to move them up or down).
Clothes Are Wet After Spin Cycle
If your clothes remain wet after your washer's spin cycle, perform the following diagnostics:
1) Lift the lid during the spin cycle. If the tub is not spinning, you may have a damaged motor coupler. Call a repairperson to replace this part.
2) If the tub is spinning, recheck the load to make sure it is balanced. If you are certain the load is balanced but your clothes are still wet, you may need to call a repairperson to replace a damaged motor pulley, tub bearing, belt, or clutch.

3) You can also follow the troubleshooting steps outlined in "Washing Machine Doesn't Drain." You may have a problem with your drain hose or pump.

Oct 27, 2011 | Washing Machines

1 Answer

Washer spins out when it feels like it!


I think you have something caught inside the pump. ie, a button, paperclip, small screw, etc.

Jun 23, 2010 | Washing Machines

1 Answer

Loud banging noise during rinse


Most noises from a washing machine occur during the rinse or spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.This will solve your problem.

Apr 08, 2010 | Whirlpool GHW9100L Front Load Washer

1 Answer

Whirlpool Ultimate Care II LSQ8243HQ0 weak spin, wet clothes


if it has a belt, it may be slipping, but you would smell a bit of burning rubber.in high use times(4 to 8 pm), the current of electric supply is low, thus less power. third, motor may need to be replaced. plz rate-bozcro

Sep 10, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

My clothe come out very wet at the end of the wash cycle


If the pump is clogged and can't release all the water it won't go into final high spin. Remove lower cover and locate coin catch and unscrew it. Water will come out, so be ready. If it's full of stuff, this is probably the problem.

Mar 13, 2009 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...