Question about Brunton 110 Volt Mini Power Inverter

1 Answer

No set up directions for my tech challenged self

I just bought a brunton solo 3.4.  I am supposed to charge it, but do not have a clue how to hook it up.  I need help I am leaving for Nepal tomorrow.

Posted by on

  • ellen610 Dec 17, 2008

    Holy smokes that was fast! thank you so much.  

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers
  • Jyackle5
    Jyackle5 Dec 17, 2008

    No Problem. Good luck

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 900w microwave trigger the LUP code & alarm?


you need at least a 1900 watt inverter with a fully charged battery to run a 900 watt microwave,it uses 900 watts to make microwaves and it uses 700 or so to run everything else.

Mar 11, 2015 | Inverter Power Inverters

1 Answer

I have a 3000 watt magnum energy sine wave inverter/ charger. It is hooked up to 5 -12 volt glass matt batteries. the charger used to charge in bulk mode @ aprox. 80 amps then absorb charge and then went...


I'm sorry that I can't help you, but if you're in a hurry, you can visit the Magnum website at: http://www.magnumenergy.com/Service/Servicefront.htm and try to find your model's online manual and search troubleshooting advice or you can email customer service at
support@magnumenergy.com and they should at least be able to lead you in the right direction.

A few questions: Does this problem remain even when there is at least a 10+ watt load on your system? is your Magnum in a hot environment? Does your inverter feel extraordinaryily hot? Have your batteries outlived their lives? Have you cleaned all the connections? Even if they 'look' like they don't need it?

All the best to you.

Sep 10, 2011 | Magnum Energy Inverter Fet Board Tfbrd3924...

1 Answer

I have a problem w the auto Gen. start turning the Gen OFF once it has started it. The lowest voltage setting to turn it off is 14.0vdc the problem w this is it will never reach that voltage. So I set the...


Your experience matches my own. I think the only solution is to use a DC monitor such as the Victron unit which has an external relay. Hook up the relay contacts to the Temp in on the AGS, then set the Victron to trip the relay when the batteries are charged to whatever percent you decide, such as 80%. Use the DC volts to start the gen and percentage of charge to turn it off......

Nov 17, 2010 | Xantrex Technology Xantrex RS2000 Sine...

1 Answer

I bought two Victor 750 watt inverters ,and was led too belive i could stack them and get 230 volts. This did not work ! why.


In order to get 230 volts out of any 115 volt inverters you would need to be able to hook the outputs up in series with each other. If your inverters have outlets there is no way to do this other than completely dismantling both units and then I wouldn't advise it. As a licensed electrcian and electronics tech I've sometime done things like that but only as experiments or in emergencies.
If your units came with a power(+) and ground(-) you could then hook them up in series by fastening the (+) from one unit to the (-) of the other, then tape them to insulate them. You should then show 230 volts from the two leads still available. On the battery side you will still hook both postives(+) to the positive(+) and both ground(-) to the negative(-).
Notes:
* Depending on the internal wiring of your units the above description may not work and could damage or even ruin your inverters.
* Although you may get 230 volts this way you will not have more power(watts,Amps) than listed for one unit and you may even have less.
* You need to also beware this could VOID any warantees and shorten the life of these units.

May 31, 2010 | Victor Power On Board 1500 Watt Power...

1 Answer

Bought a new vector maxxsst 1200 watt inverter


Inverter run on batteries sir, and if these batteries are not charged, the run time {the number of hours it will work} reduces.
S0, you will need to connect the inverter to a power source.Theses will allow your batteries to be charged and enable it to run for a long period of time.
Make sure your batteries are still OK.i.e working properly

May 03, 2010 | Vector ® Maxx SST 1200 - watt Power...

1 Answer

I need to change the window of a brunton compass and I want to know how to keep of the broken window


I'm sorry this hasn't gotten a response, but I'm afraid the problem isn't stated very clearly. Perhaps some words are missing from "how to keep of the broken window", because I certainly can't figure out what the question is.

Feb 05, 2010 | Brunton Power Inverters

2 Answers

MICROTEK INVERTER HELP


Bad batteries, replace all of them together.

Oct 02, 2009 | Power Inverters

1 Answer

No power output from my vector 1000w inverter.


Sounds like a ground issue,Try this,Take the jumper cables and hook just the neg clamp tho the battery and the other end to the case of the inverter for a direct ground and see if that works..

Please rate this fixya

Jan 26, 2009 | Vector 1000w Power Inverter

1 Answer

Can't get power to my RoadPro 1500 DC to AC Power Inverter


I have had this same problem with several power inverters over time. The problem is usually one of three things.

Those starting with the simplest.

1. Too much current being drawn on the inverter.
Solution (Check appliances that are plugged in and make sure they are not drawing more than 1200 watts. If they are unplug the appliance that is using the most current and get an inverter that is more suited to your power needs.)

2. Some power inverters have fuses built on to them. Sometimes multiple fuses. Sometimes, one fuse may burn out leaving one intact. When this happens even small items draw too much current and over load the inverter.
Solution (Replace the fuses)

3. Improper installation. Inverters draw a lot of current. You must use the propper wire size for the inverter. I would recomend at least an eight guage wire directly fused and hooked directly to the battery. Of course like with all things the bigger the wire the better the flow of electricity.

If it is not one of those things stop into a truck stop electronics shop and have the person diagnose it.

Hope that helps.

Jan 20, 2009 | RoadPro AC/DC Power Inverter 2000/5000w

Not finding what you are looking for?
Brunton 110 Volt Mini Power Inverter Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brunton Power Inverters Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

fisherman816
fisherman816

Level 2 Expert

66 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Brunton Power Inverter Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...