Question about 2-Way Remote Starter

3 Answers

COOL START REMOTE NEEDS REPROGRAMMING

I HAVE A COOL START REMOTE # M65TX605 THAT NEEDS TO BE REPROGRAMMED. IT WAS WORKING A COUPLE OF DAYS AGO BUT WHEN I TOOK IT OUT MY POCKET THE LIGHT WAS FLASHING. NO BUTTONS WERE PUSHED SO I BELIEVE IT ENTERED INTO THE PROGRAMMING PHASE AND I DID NOT GET THAT INFO FROM THE INSTALL DEALER.

Posted by on

  • Anonymous Jan 22, 2009

    remote works for a couple weeks with new batteries then does not lock doors or start however the blue light still works. ???

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

From http://www.crimestopper.com/techweb/InstructionBooks/RemoteStart/rs1300dp_1304dp_a_ops.pdf Note: All transmitter codes must be learned at time of programming!! The unit will learns up to 4 different transmitter codes. 1. Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire). 2. Turn key to the ON position. (Pink wire must be connected.) 3. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off and close hood. See diagram below.

Posted on Dec 23, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

So this morning i tried to remote start my truck the truck turned on and it stayed on for 5 sec turned off again 3 sec later it turned on again for 5 sec and turned off agin doin the same problem over and over any ideas what this problem can be>? its the cool start idk which model # i bought the truck with it

Posted on Nov 18, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My remote was droped the buttons on the side will cause the light to come on but the rest of the buttons wont do anything at all how can i fix this

Posted on Dec 31, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat stop working on 2010 GMC Terrain.I changed the Thermostat it worked for couple of days than it stop working than I saw it needed more antifreeze because it was low.


you have a air lock...Start the car with the radiator cap off. One of the easiest ways to bleed your car's radiator is to simply remove the radiator cap and then start your engine. Leave the vehicle running until it reaches its normal operating temperature. It may take between 15 or 20 minutes before your car generates enough heat to push out the air that has been trapped in your car's cooling system. You may find that you need to add additional coolant, as air pockets can artificially inflate coolant levels.
hope this helps

Jan 04, 2018 | GMC Cars & Trucks

1 Answer

I have had the Avital 4103 installed in my truck a couple of years ago. Over the last few days while driving, the horn alarm goes off by itself. It is happining about every 5-10 minutes. I need to keep...


The bypass module is most likely interfering with the vehicle data causing the OEM security to trigger. Take it to a security/remote start retailer and have the bypass module reprogrammed or replaced.

Apr 06, 2014 | 4103LX 4Button Remote Start System with...

1 Answer

Car is "dead" but battery/alternator/starter are all in working order. Hornet is causing this.


Sounds more like a faulty battery terminal to me from your description ,try cleaning and make sure its tight then smear with petroleum grease.Clean terminal with a kettle of hot water first

Jul 26, 2013 | Cars & Trucks

1 Answer

Goog day. I have a Samsung LE40A559 LCD TV and about a week ago it stopped responding to the remote. Remote itself is working as when the TV is off and I push buttons on the remote the blue light on TV...


The flashing blue light shows that the TV is receiving I.R. from the remote but doesn't mean that the signal being received is recognized by the Samsung. If you have a "universal" remote then your TV code may need to be re-entered/reprogrammed...changing batteries in a "universal" will usually require it to be reprogrammed.

Also...because of the remotes construction (rubber membranes with carbon dots that short across PC traces) I've seen certain buttons stop working altogether.

Nov 05, 2010 | Samsung TV Remote Control

1 Answer

2001 volvo S60 door would not unlock with key


key needs to be reprogrammed at volvo dealer

Jun 04, 2009 | 2001 Volvo S60

1 Answer

Toshiba md12m1 tv/dvd, original remote needs reprogramming


i have a toshiba tv how do i reprogram it ,evry time the electric goes out the tv goes out to be reprogram and i for got how and do not have i book.

May 04, 2009 | Toshiba Televison & Video

1 Answer

Remote does not open garage door


It sounds like the wall button has the lock feature engauged.

Is there a small green LED flashing inside the wall button?
Push and hold the lock button for about two seconds and the LED should stop flashing. This will unlock the garage door opener and your remotes should start working. You may have to reprogram your remotes and homelink again since you triedprograming in the lock mode.

Good luck.

Jan 20, 2009 | Chamberlain 950CB Remote Control

Not finding what you are looking for?
2-Way Remote Starter Logo

16,818 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crime Stopper Vehicle Parts & Accessories Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22393 Answers

Frank Mangiapane

Level 1 Expert

36 Answers

Steve
Steve

Level 3 Expert

696 Answers

Are you a Crime Stopper Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...