Question about Dyna-Glo RMC-8001SS Heater

1 Answer

Dyna Glo model 95 C2 wick replacement is a boogar even with so called instructions is there any trick to this wick is hard to hold in place and insert over round housing without pulling out 3 sidepins have tried many times cannot hold everything together

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Turn the wick control knob all the way up before installing new wick. Put it all back together and make sure wick goes all the way down inside the groove when you push the shutoff lever. Do this several times. If not, then heater WILL NOT shut off !! P.S..use clear K-1 kerosene....the K-1 with red color seems to make bad carbon deposits on the wick...in a short time the wick becomes crusted and will not drop down to extinguish the flame. I had to open it up and put baking soda on the wick to put it out.

Posted on Jan 30, 2009

  • RedDawg_A1 Jan 30, 2009

    Have someone help you and guide the bottom of the wick(not the cut off end) down onto the center round hub.Also...wait 1 hour before lighting the heater to give the wick time to absorb the K1 all the way up . Good Luck

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Dynaglo RMC-95 in Nigeria and the wick is bad . Where and how can i get replacement.


Most hardware stores and home centers carry wicks for kerosene heaters, in season. Since you know your model number, it won't be hard to find one there.

Jun 27, 2011 | Dyna-Glo Heaters

1 Answer

Need to see pictorial instruction on how to replace wick in a Dyna Glo RMC-95-C2 kerosene heater


I think the Dyna-glow RMC95 series of heaters are equivalent to DH2300 series heaters.
In any event, the wick you purchased should have ahd the installation instructions included with the wick.

If it didn't or you tossed it, Here's a link to the DH-2300 series heater's Owners Manual, which may help you.

http://www.yourheater.com/DH2301-3%20owners%20manual.pdf

Good luck. Be sure to wear rubber gloves when you try to install the wick. Particularly, if you still have kerosene in the tank.

Feb 11, 2011 | Dyna-Glo RMC-8001SS Heater

2 Answers

I just replaced the wick, cleaned up the heater and filled with new K-1 kero. The heater (Dyna-Glo RMC-95-C7) is emitting black smoke worst than ever. The wick is burning a little unevenly.


Either the wick was improperly installed or you may not have allowed enough time for the wick to soak in the kerosene and become evenly distributed. Check the placement of the new wick and allow time (several hours) for the wick to absorb the kerosene.

Jan 31, 2011 | Dyna-Glo RMC-8001SS Heater

1 Answer

Have a Dyna Glo RMC-95-C2 and I can't get it to lite.


You have to change the batteries.. the manufacturer shipped it with **** batteries.

also take it apart.. very simple and clean out any soot..

Soot will cause heavy smoking...

The wick should last more than a year ....

Dec 14, 2009 | Dyna-Glo RMC-8001SS Heater

1 Answer

Kerosene heater


Dyna Glo 95 c4 Manual
http://www.owneriq.com/mdownloads/8979e0af-dfee-45f1-a8ba-c05c2f5ed4a8.pdf

Jan 31, 2009 | Dyna-Glo RMC-8001SS Heater

1 Answer

I need to buy a replacement wick


You can get them at Lowes for less then $10.00 Number DH-145

Dec 23, 2008 | Dyna-Glo RMC-8001SS Heater

1 Answer

Help


Dyna Glo 95 c4 Manual
http://www.owneriq.com/mdownloads/8979e0af-dfee-45f1-a8ba-c05c2f5ed4a8.pdf

Aug 31, 2008 | Dyna-Glo RMC-8001SS Heater

4 Answers

Can not replace wick in dyna glo serial number RMC-95-C2


As "guest" reported, the wick replacement for RMC95 series is the same as his posting for the DH2301.
After calling my local Tractor Supply and searching the net, I had it but it ain't easy. My sleeve doesn't come out necessitating cranking the knob up (wick will be level with the top) find the three holes (more like two are slot and one is a hole) then where the diagonal grooves are, there is ANOTHER HOLE which you must snap the pin in both of those all at once!
The good news is, you get one in, the rest are cake. I was pretty frustrated so I hope this helps others.

Dec 08, 2007 | Dyna-Glo RMC-8001SS Heater

Not finding what you are looking for?
Dyna-Glo RMC-8001SS Heater Logo

718 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyna-Glo Heaters Experts

paulcarew

Level 3 Expert

1875 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

drifterray

Level 1 Expert

10 Answers

Are you a Dyna-Glo Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...