Question about Lucent Pipeline 130 Router

1 Answer

How to upgrade firmware from 6.1x to 7.4x, and where to find it?

Pipeline 130 router model p130-urbi-t1-asa

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Log in to belin website "www.belkin.com/uk/support and download the firmware under software and firmware section.
once u download it lof in to your router unterface by connecting the rtr to ur comp.
open the internet explorer and typr 192.168.2.1 and on the router interface u have firmware update clikc and browse te file u download and click update that r bye............

Posted on Dec 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for an updated firmware version for model WRT54G


Upgrading the router's firmware will give it numerous functions. This includes a more stable connection to the internet.

To upgrade the router's firmware, complete the following steps:

i. Downloading the Firmware
ii. Backing-Up the Router's Settings
iii. Upgrading the Router's Firmware
iv. Completing the Firmware Upgrade
v. Restoring the Router's Settings
vi. Completing the Firmware Upgrade Process

NOTE: Before proceeding with the upgrade, your computer must have an active Internet connection. It is also recommended that you use a wired computer in upgrading the router's firmware.

Nov 06, 2010 | Linksys Wireless-G WRT54G Router

2 Answers

After over a year of good use, the past 2 weeks have seen the router repeatedly lose the internet connection after a minute or so of use. It reboots ok initially but then loses the connection again.


Try to upgrade the firmware of the router.
Is there any computer connected to the router with the cable.
If not then you will need to connect the computer to the router.
Download the firmware of the router from the manufacturer's website.
enter the model number. select proper version number and download the firmware of the router.
Once you download the firmware, you will need to open the router set up and upgrade the firmware of the router.
After upgrading the firmware, it is recommended that you reset and reconfigure the router.
Click Here for more information about router and networking

Oct 11, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

Wireless-G WRT54G Router: how do i upgrade the firmware...


Is there any computer connected to the router with the cable.
If not then you will need to connect the computer to the router.
Download the firmware of the router from the manufacturer's website.
enter the model number. select proper version number and download the firmware of the router.
Once you download the firmware, you will need to open the router set up and upgrade the firmware of the router.
After upgrading the firmware, it is recommended that you reset and reconfigure the router.
Click Here for more information about router and networking

May 06, 2010 | Linksys Wireless-G WRT54G Router

2 Answers

How do I upgrade firmware?


go to linksys download upgrade and follow instructions

Feb 19, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

We just replaced our T1 with Cox cable internet access. Now the internet is incredibly slow through the Linksys BEFSX41, but fast is directly plugged into the cable modem. What can I do to fix that?


HI Friend
You have to upgrade the firmware of your router. To do this please follow the steps

1. Open the website www.linksys.com/download
2. Enter the model number of your router and hit enter
3. Now click on Get downloads and drivers
4. Select the version number of your router and scroll down a little.
5. To your left you will see Downloads and under that you will see Firmware
6.Click firmware and save it to your desktop
7. Now again open internet explorer and in the address bar 192.168.1.1 and hit enter
8. If you have not changed the default password of the router then leave the user name blank and in password type admin and hit enter.
9.Now click Administration and under that click Upgrade firmware.
10. Select the file and that you have saved on your desktop and click upgrade.
11.After upgrade turn off the router for 30 seconds.

Enjoy

Regards
Chiranjeet
4.

Dec 16, 2009 | Linksys BEFSX41 Router (DHBEFSX41)

1 Answer

I'm trying to upgrade the firmware on a belkin wireless router


upgrade of Firmware is at your risk...
never upgrade Firmwares....they are not ment for that....
your hardware may be rendered useless after firmware upgrades....the chip inside your hardware is programed to run based on a certian program installed as a firmware from the factory....sometimes upgrades will screwup your hardware....so be careful and do it at your own risk...

Dec 10, 2009 | Belkin (F5D7230-4) Router (587009)

2 Answers

What is a Lucent Pipeline P130-u-v35-asa used for


The short answer is.... It is a T-1 Router/Firewall that works with ISDN and Frame Relay. It uses the V.35 and BRI interfaces and requires an external CSU/DSU. It is NOT compatable with Cable or DSL internet service providers.

Oct 29, 2009 | Lucent Pipeline 130 Router

2 Answers

A really bizarre problem with WRT-160N. I have the Network Connection Status open and the connection speed cycles thru from 130 Mbps down to 1.0 Mbps within about a minute. It keeps doing it! I have never...


i had that happen with my wrt54g it would go from 54 to 1 and start over again well i learned my leason there i tryed reverting to the original firmware and ended up toasting my router so dont try that :) im not to sure what the cause of this is either i do think that it in the router and not the wifi card tho

Sep 30, 2009 | Linksys WRT160N Wireless Router

2 Answers

Osicom ROUTERmate T1 Drop and Insert CSU/DSU (RM-T1/D1/R)


Aw man your in a pickle here. I used to know a man named Mike Sandman when I worked in Chicago goto his website www.sandman.com If anybody knows how to reset or hack the managment pass its him. I'm telling you as far as Telecommunications stuff goes Mike is like Leonardo Da Vinci

May 02, 2008 | Osicom ROUTERmate DI (RMATE-T1/DI/R)

1 Answer

How to upgrade the firmware on a BEFSR41


Firmware upgrades may erase all previous settings to your router's configuration. Before upgrading your firmware, make sure to record your settings. 1. Unplug and disconnect all computers from the router except for one. This computer must be plugged into the router directly. There can be no other network activity on the router during the upgrade, so be sure to power off all other computers. 2. Go to http://www.linksys.com/download 3. Select the model number of the Linksys router you have (BEFSR41) as firmware upgrades vary by model and version. You can find your router version underneath your router after the model number. For example, ?BEFSR41 Ver. 3?. 4. Click the Downloads for this Product button. 5. Once you arrive on the download page, click the Firmware button. 6. After the firmware page opens, click the link that says ?Click here to download the latest firmware...? and download the firmware file to your computer. 7. Once you download the firmware Zip file, unzip it. If you do not have an unzipping program, go to http://www.winzip.com and download WinZip, which will allow you to unzip the file. 8. After unzipping the firmware files, one of them will be called TFTP.EXE. Double click on it. 9. When the ?Upgrade Firmware? window opens, you will have three prompts. The ?Server? field is for the IP address of your router; by default this would be 192.168.1.1. 10. Enter the routers password into the ?Password? field; by default the password is admin. 11. Browse for the file in the Firmware Upgrade utility program by clicking on the button next to file with the '?' symbol on it. Look for the file named 'code.bin' in the folder where the firmware files were extracted to. 12. Highlight the code.bin file and click on the Open button to direct the TFTP loader program to put that file into the "File" box. 13. The full path should be displayed [example: c:\linksys\code.bin]. 14. Click on the Upgrade button to begin the upgrade process. 15. The upgrade should take about 1 minute, and you will be prompted after the upgrade is complete and successful. If you are still having troubles, contact Linksys Technical Support.

Feb 16, 2006 | Linksys EtherFast Cable/DSL Router

Not finding what you are looking for?
Lucent Pipeline 130 Router Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lucent Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Mike

Level 3 Expert

4331 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Lucent Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...