Question about PC Desktops

1 Answer

White - at my Harddisk boot, Its happear again after i reformated my pc

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If you have a lcd monitor it is fried. if it is under warranty return it. if not get a new one

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reformat my pc


Hi Good day!! Sir/Madam if you want to format your pc you will need and CD of a Operating system like WindowsXp/Vista/etc.(note you should have the product key after installing the OS)
here are the steps on reformating:
1. Open your Bios setup by Pressing del or f2 it depends on your board.
2. insert your bootable CD on your CD/DVD rom.
3. go to boot setup, set your boot priority 1st boot must be your CD/DVD rom, 2nd boot your harddisk after you set your boot priority press f10 and then save changes. it will restart your pc.
4. your computer will boot in CD and a message will appear "Press any key to boot from CD...." you should follow it. press any key!! if you boot from cd successfully you should be on windows setup it is a blue screen!! congrats!!
5. windows setup will load it's driver, when finish loading there will be a option on the bottom.
6. press f8 for terms and agreement (read carefully)
you can start formating just read the instruction.

REGARDS
JR

Oct 14, 2010 | PC Desktops

3 Answers

Will not reboot


did u by chance change any settings in the bios.... if yes please change the settings.... if u donno hw to chnge the bios settings... please ask me...

Jun 07, 2008 | Compaq Presario 5000 PC Desktop

Tip

If you get message: " boot disk failure" then follow this tip


1)If any cd or dvd is there in the cd or dvd drive remove them first then try booting
if problem persists then
2)check the boot device priority in the BIOS menu,change the boot device priority if required(change to 1 st boot device floppy, 2nd harddisk drive,3 rd to cdrom drive something like this)
to go to bios setup press del or f2(it depends if del key doesnt brings you the bios utility then press f2) at time when you switch on the pc ie at the time of booting the pc ,
if problem persists then
3)check whether the harddisk is detected or not in the bios setup
if it is not detected then just open the CPU & check the bus & power supply cable connected to the harddisk remove them & reinsert them ...
if required then replace with the new ones ....
if the problem persists then
4)the operating system might have got corrupted just reinstall ....
if problem persists then
5)the harddisk partitions might have got corrupted or crashed ,just try partitioning them again and by installing the operating system.

on Aug 28, 2008 | Compaq Presario 5000 PC Desktop

1 Answer

When I turn on my dell the processor fan comes on at high speed, but will not boot.The computer booted the night before and had no problems. I aam using a friends computer to send this problem.


First pull cmos cell from motherbord for 10 minutes so all settings defaults.
Then pull RAM memory clean dust from all circuits Put RAM in its position.
Then check .
If still same issue then reconnect ATX power connector from smps power supply to motherbord.
Dis connect harddisk connection and then check .
If you get display then connect harddisk connection again.
Then also open processor fan and processor then fix both again.
Then power up press F1 or F2 or "del" to enter in bios .
Then check in bios harddiks is detected or not?
Let me know if you need more assistanse.
Thanks.

Aug 31, 2009 | PC Desktops

1 Answer

Es2 300x not boot up


Open your cpu cabinet.
Refix your RAM clean all dust from circuit bord.
Reconnect power cable and ide or sata cable to harddisk.

Reconnect processor fan and processor.
Reconnect power supply from psu to motherbord.
Pull your cmos cell from motherbord for 15 minutes from motherbord so all settings are reset to defaults.
Check in bios your harddisk is detected?
For boot your computer with operating system your harddisk must detect in bios.

Aug 15, 2009 | PC Desktops

1 Answer

Harddisk problem


clean all the components of your pc then put it all again to its respective places.. if it boots configure the cmos settings and load the defaults... this problem is not cause only by bad harddisk.. it may also be caused by other components of your pc

Jul 21, 2009 | PC Desktops

1 Answer

Acer 3050 won't boot. Disk Read Error


looks like hardware failure.



find out what harddisk exactly you do have in the bios :
- press Del or F1 or F2 during booting, goto IDE devices, look for the model, size (in GB) etc.,
write down (the manufacturer could be: samsung, seagate, maxtor, fujitsu...)

- then change order of boot devices so that cd/dvd-rom drive and /or 3,5 '' floppy drive boots
before the harddisk, exit saving changes (F10 or Esc)

- then get diagnosis program from the harddisk manufacturer's homepage,
copy that to a bootable floppy disk or burn it to a cd-r/cd-rw which must be bootable
- boot from the cd or floppy, run diagnosis tool, both short and long test, what does it say then?
- if hardformat is available, perform one
- might work now, at least the hd will be recognized
-setup new windows installation.
have fun







Apr 21, 2009 | PC Desktops

1 Answer

Boot issue


Boot device means the harddisk...check the kabels.
Is there power on the harddisk?
If this not helps than....
when the pc starts up push delete view times...than your must be in the bios.
push f5 than push f10 and enter...
The pc restarts.....if thre are the same problem.
Come back here and we try to find out next...

Jan 07, 2009 | HP Media Center m7250n (ED842AA) PC...

1 Answer

Disk Boot Failure


you need to select ur harddisk as the first bootable device., that option is in BIOS settings. When switch on the system before loading OS press F2 to get the BIOS settings and select boot option in the menu and select your harddisk as the first bootable device. Restart the system now. If the same error is displayed your harddisk data cable may be failed or your harddisk may be corrupted...

Jul 11, 2008 | PC Desktops

1 Answer

IBM Netvista 6059 - Can't upgrade to windows XP


Right well XP Pro really MUST be formatted with NTFS only... I suggest you get a third party partitioning program like Partition magic and completely remove the partition & redo it all again & this time Format NTFS. Or if ya have a WIN98 boot disk, and ya can use FDISK, Delete ALL partitions, and remake them again, using all the disk space, then format as NTFS, then proceed as below Then using your windows XP PRO setup Disk, start the install ...then when asked about where you want the install located, select C & REFORMAT it AGAIN with the windows setup using again NTFS file system... this should finish & then the Install should "see" your entire hard drive and format it accordingly and then when finished you can proceede to install XP.

Sep 04, 2007 | IBM NetVista PC Desktop

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...