Question about Kenmore 40494 / 40495 / 40499 Electric Single Oven

3 Answers

My kenmore electronic stove is having a beep with code F1 on the

Screen . please help!!!
thanks,

Posted by on

  • 1 more comment 
  • lightbender4 Jan 20, 2009

    The oven and timer functions will not work it makes a loud beep, then it goes dark

  • Tina03 Feb 03, 2009

    Kenmore dual fuel code eo f1 then there was a spark and the whole pannel went dark and now won't do anything

  • Jyackle5
    Jyackle5 May 11, 2010

    I need to get a model # to help.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Posted on Dec 18, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

My Roper was doing this for no apparent reason. Buzzer would wake me up at 3am. Buzzer never went off when using the range.
I've gotten used to turning off the range circuit breaker after using the range. My solution. --Remove ERC board and unsolder the buzzer.

Posted on Nov 06, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Stove needs new thermostat mine did same thing also clock

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an amana artc8600 and the error code it has is f1. could you tell what the code means. Also, when i try to turn the oven on no matter what setting it keeps turning off i have to try a bunch of...


HI,
Disconnect power to stove
Gain access to the back of the clock (electronic range control or ERC).
Unplug the pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
Make sure everything is clear and will not short out when power is turned back on.
Turn power back on to stove.
Watch for the F1 and the beep
If you see f1 and hear the beep its the ERC
If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.

Thank you for using fixya
Leo Ponder
Please rate me if this helped.

Jul 23, 2011 | Ovens

1 Answer

Error Code F1 displays once in a while. What does it mean?


How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
1. Disconnect power to stove
2. Gain access to the back of the clock (electronic range control or ERC).
3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
4. Make sure everything is clear and will not short out when power is turned back on.
5. Turn power back on to stove.
6. Watch for the F1 and listen for the beep.
7. If you get the F1 and beep, replace the ERC.
8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.

* ERC - Electronic Range Control

NOTE: Some models incorporate the touch pad and the clock as one part.

Hope helps.

Apr 20, 2011 | Ovens

1 Answer

What could be the problem if F1 code and beeping in GE wall oven/


F1=Touch control pad and or Clock defective.
How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
    NOTE: Some models incorporate the touch pad and the clock as one part.

Jan 11, 2011 | Ovens

1 Answer

F1 and beeping sound on electric stove model FEF365BWF


Hello, the F1 and the beeping sound is as a result of the Electronic oven Control Failure (EOC), and you need to replace the electronic oven control also called the EOC or clock.

Thanks

Jun 13, 2010 | Frigidaire FEB24S2AS / FEB24S2AB Electric...

1 Answer

My oven when turned on goes to F1 and the heat is like broil...only the top burner comes on????


Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

May 28, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

F1 beeping


hello there:
Please read this carefully and follow the tips and this will help you find out what is exactly the problem ok
How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
    NOTE: Some models incorporate the touch pad and the clock as one part. * We have seen a few of the newer Maytag ranges with a F1 fault code and the problem was the oven temp sensor, check carefully the wires to and from the oven temp sensor!!

Jan 12, 2010 | GE Profile JTP56 Electric Double Oven

2 Answers

The stove just says F1 and beeps won't let me do


Hello with the limited information and no make or model I can only give a generic response to this one. Most manufacturers F1 code indicates a bad control board (EOC) and or a bad touch-pad. If you have any other questions please feel free to comment. Mike

Nov 03, 2009 | Ovens

1 Answer

F1 signal started today can't turn the alarm off.model kenmore 9114832593


How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  • Disconnect power to stove
  • Gain access to the back of the clock (electronic range control or ERC).
  • Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  • Make sure everything is clear and will not short out when power is turned back on.
  • Turn power back on to stove.
  • Watch for the F1 and listen for the beep.
  • If you get the F1 and beep, replace the ERC.
  • If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
    NOTE: Some models incorporate the touch pad and the clock as one part.

  • Let me know if this doesn't point you to a solution. There are a couple of more things to try.

    Feb 01, 2009 | Ovens

    1 Answer

    Beeping F 10


    Hello
    Welcome to fixya.com

    You r answer to the F10 code is:

    The F10 error code indicates a runaway oven temperature. This would indicate that the oven temperature sensor or the electronic control has failed. According to the service manual you need to unplug the range & after restoring power the oven continues to overheat you will need to replace the electronic oven control.
    This a job for a hands on tech!

    Thank you for trusting us with your questions.
    Please remember to leave a solved rating before you sign out!
    Thank You

    Dec 25, 2008 | Kenmore 40494 / 40495 / 40499 Electric...

    1 Answer

    My kenmore oven is beeping and will not stop. the display shows F-1.


    Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

    KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
    F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

    KENMORE - 911 Series (General Electric/Roper)
    F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

    KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
    F1-E0 EPROM Error - Electronic Range Control (ERC).
    F1-E1 EPROM Error - Electronic Range Control (ERC).
    F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
    F1-E3 Fuel Type Fail

    Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
    “9” for gas-If code changes again-replace Electronic Range Control (ERC).

    KENMORE - 790 Series Electronic Oven Control (Frigidaire)
    F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
    Runaway Temp = Replace Electronic Oven Control (EOC).

    Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

    Dec 16, 2008 | Ovens

    Not finding what you are looking for?
    Kenmore 40494 / 40495 / 40499 Electric Single Oven Logo

    2,180 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kenmore Ovens Experts

    Mike Cairns
    Mike Cairns

    Level 3 Expert

    3053 Answers

    Michael Thomas
    Michael Thomas

    Level 3 Expert

    3051 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Are you a Kenmore Oven Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...