Question about Kenmore 74832 Gas Dryer

1 Answer

77732794 where can i find the fuse

Posted by on

  • tony olmeda May 11, 2010

    you should have a one time fuse located on the heat tube and possible another fuse


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Kenmore Master
  • 8,147 Answers

77732794 - d9c57bf.jpg

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i test a thermal fuse?

Unplug the dryer. Remove the wires going to the fuse, you do not need to remove the fuse from the dryer. Use a continuity tester between the two terminals of the fuse. If there is continuity the fuse is good, if not, the fuse is bad, replace it.

Sep 02, 2014 | Whirlpool Dryers

1 Answer

How do I know if the fuse is bad in my dryer

It depends on what fuse you're talking about. They have 3 or 4 different fuses. The thermal fuse will prevent the dryer from turning on at all. The other fuses are for the heating element. Those fuses dont go bad that often.

Sep 25, 2013 | Dryers

1 Answer

Replaced thermal fuse in kitchenaid keys777 eqo dryer if started working then it has blown another thermal fuse .had a spare fuse .what could cause fuses to fail,thanks

There is a high limit and low limit switch also in the circuit. If either of these fail, it can blow the fuse. Also, if your heating element is shorting to ground, it will blow the thermal fuse. It is standard practice to replace the high and low limit switches with the thermal fuse.

Apr 30, 2012 | Dryers

1 Answer

Won't power on

There is no fuse box, all there is for fuse protection is the electric drive motor "thermal fuse" and it is located inside the dryer cabinet near the drive motor. If the fuse blew then you have a problem, find out what that is before putting another fuse in it, you can create a fire hazard.

Feb 07, 2012 | LG DLEX2501 Dryer

2 Answers

Amana dryer model YNED7200TW will not start. there is power, but start button does nothing. Resetting breaker did not work. Any ideas?

Thermal Fuse

Item #2986 (OEM Part)

Thermal fuse. If the dryer overheats, this device stops the flow of electricity to the heat source and/or the entire dryer. It is located on the blower housing and cannot be reset. The most common cause for overheating is a vent tube clogged with lint, a birds nest or other debris.

Manufacturer Number 3392519

  • Admiral Dryer Thermal Fuse
  • Amana Dryer Thermal Fuse
  • Crosley Dryer Thermal Fuse
  • Estate Dryer Thermal Fuse
  • Kenmore Dryer Thermal Fuse
  • Kenmore Refrigerator Thermal Fuse
  • Kenmore Washer/Dryer Combo Thermal Fuse
  • KitchenAid Dryer Thermal Fuse
  • KitchenAid Washer/Dryer Combo Thermal Fuse
  • Magic Chef Dryer Thermal Fuse
  • Maytag Dryer Thermal Fuse
  • Roper Dryer Thermal Fuse
  • Roper Washer/Dryer Combo Thermal Fuse
  • Whirlpool Dryer Thermal Fuse
  • Whirlpool Washer/Dryer Combo Thermal Fuse

In Stock

Jun 08, 2011 | Amana Dryers

3 Answers

My whirlpool dryer keeps blowing the fuse for heating. The dryer will still tumble but once stopped, won't start until the fuse is replaced. We've cleaned the whole thing out and even set up a different...

I would check the outlet as it sounds like one of the wires is off/shorted. Here is a website that may assist you, Good Luck Tim:

Nov 01, 2010 | Kenmore 63932 Electric Dryer

1 Answer

I am looking for where to find the fuses for this Kenmore Electric Dryer. Can you help?

which fuses?the electronic control board fuse or the main power fuses,the electronic fuse is on the control panel behind the front,the main fuses that heat the dryer are in your homes power panel

Aug 01, 2010 | Dryers

1 Answer

Gas dryer starts to tumble but it doesn't get hot and dry clothes

It's either a ignitor or the gas valve. Is this something that you could work on?

Sep 02, 2009 | Kenmore 63942 Dryer

1 Answer

Dryer won't heat

i am sending you all the possibilities for your problem, check either of these causes ----and than let me know if it is solved----

Power from the house
Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.

Heating element
Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.

Thermal fuse
On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)

A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.

Aug 11, 2008 | Kenmore 74832 Gas Dryer

Not finding what you are looking for?
Kenmore 74832 Gas Dryer Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides