Question about JVC RX-664V Receiver

1 Answer

JVC PC X-95 Boombox

I am fixing this boombox for a friend, The radio works as well as the tape player. The problem is the CD player. If you insert a CD, 'Cd' comes up on th display screen as wel as"OO0000" but the table doesn't turn. If I can get into the unit, I can probably find the problem and fix it. I need help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Its moe than likely your laser. try swabbing it with a q tip and alcoholif that doesnt do it it might be the motor.

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Philips mcm9 system won't read any cds. It says "reading" but nothing else happens and even says that when there is no cd in slot, radio & tape are both working and cd player was working...


In most cases when the CD does not play it is possible that the optical head is a suspect. Sometimes it might pick up ordinary audio CD but will not play other formats. This indicates that the optical head is weak and so there is no detection or scanning of the CD . If the optical is working the tracks will be read immediately but with no scanning the laser head can be defective.

If the no disc comes even without a disc in the player you must check and see if there is a mechanical fault specially in the loading section that seems to trigger the CD mode to work.

Also check to see the main motor as it will not work in some cases as unless the tracks are read the drive motor will not work with signal from the processor. Also in some cases the central motor base can shift and so the distance to the disc can be more resulting in low detection. You can pull up the spindle to come closer.
Sometimes certain cleaner disks will not be tracked to run for cleaning as it will not be read and so will reject. Hence it is ideal to manually clean the laser head eye using a cleaning swap /cotton bud with gentle pressure on the lens eye.
If there is no result then watch if the CD spins or tries to spin. If so the board seems to work unless a test is taken on the main board but the possibility of a defective optical head can be the suspected fault.
If any of the above seems otherwise we must recheck with possibilities of a malfunction of the main processor board

Jul 29, 2011 | Audio & Video Receivers

1 Answer

I inherited this dual-deck amplifier from an uncle who has passed on. Unfortunately there is no manual with it anymore. The buttons on the tape decks don't depress except for the stop which immediately...


Hello
It's hard to provide advice without knowing make / model number. Many manufacturers have back issues of owners manuals on their websites - if not a Google search will often trawl one up
Lots of manufacturers used to put 'soft touch' buttons on cassette players - they don't actually push in (just wobble a bit) but work nonetheless. From your description it sounds like the drive belt has broken - alternatively it could be some worn cogs in the motor system, which might explain the clicking sound. Many years ago I had an AIWA tape deck that made a loud clicking when the tape counter got to 9999. Pressing the counter reset used to clear it.
You should be able to connect a CD or DVD player to it using the auxiliary sockets on the rear panel (assuming it has some). Any tape/ aux inputs should be the right impedance to work okay but a phono (record player) socket is unlikely to match. There will normally be a row of buttons (or perhaps a rotary dial) on the front to select input source.

Mar 23, 2011 | Audio & Video Receivers

1 Answer

Hello, I have found a Sansui DA-T550 music-system with AM/FM stereo tuner, integrated amplifier, cassette deck and turnable/gramophone (placed separated). It seems like the system is working OK. My...


Hi!

I have the same deck. Did it come with rammophone or are you using your own grammophone?
I have it with original grammophone and I don't need a remote control, I don't even have it. You just turn on your grammophone and it is automatic, just place the needle on record and it should switch and play automatically. That is if you have connected the wires right (two wires for sound, one for automation, all in the same area).

If you have separate grammophone, I am assuming you just need to place two wires into the separate phono channels and it should work. There is just no automatic detection, so you have to swithc to mono manually: There is a button on the right, beside Volume control "tape to CD" or something.

To play the tape, just simply push the play button on the bottom, should work, or you could try tape to cd button off and see if it detects automatically when tape is inserted.


Currently I have it taken apart and there is tape detection system apparent. Its quite automated reciever, which sucks, because all kinds of problems appear and it is difficult to fix.

On my Sansui, the tape player starts winding slowly when pressed play button. And the tape motor seems to be on always, even when the tape is not used, and the motor is really loud. --Need to find a solution to this problem. And I hate it switch to radio/FM every time the record stops. Plus the original grammophone doesn't work correctly, it is supposed to take off the needle when record reaches an end, but it just pushes the neelde to the holder... over the record..... "screeeeech".

Nov 15, 2010 | Audio & Video Receivers

1 Answer

I have inherited a Sanyo 3-disc CD changer system with radio and tape-to-tape deck. When I tried to put a CD (a copy made on my computer) into the system it would not play, so thinking it wanted a...


i have the same problem and when I opened it I noticed that it wasn't spinning the disc fast enough, if anyone knows how to fix this or if we can just swap the motor please help!!

Sep 17, 2010 | Audio & Video Receivers

1 Answer

Speaker cuts out when ipod is hooked up to audio in port


try isolating the problem by inserting other sources such as tape deck, portable cd players, game consoles, if they work fine, test you ipod cable. next test you ipod on other audio in ports such as karaoke or other component stereos, ask a friend if he or she has one. test both, you may now have the idea where the trouble is.

Jul 10, 2009 | Teac AG-V2050

1 Answer

No sound is being produced from the cd player unit. I get sound from the radio receiver and the tape deck. Also, when the CD player is on and the volume is turned up to the max, I can hear the music very...


Try looking for the reset button usually a little pin button like the ones on digital wrist watches hard to notice. If this is a home stereo are you sure the tape monitor button isn't on?

Dec 01, 2008 | Audio & Video Receivers

Not finding what you are looking for?
JVC RX-664V Receiver Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4753 Answers

Rod
Rod

Level 2 Expert

224 Answers

Are you a JVC Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...