Question about Kenmore 44102 Front Load Washer

2 Answers

Kenmore Front load washer didn't complete the cycle.model #44082

I started a wash cycle, signal didn't go off. Went to check why? the washer had 2 minutes left on it , but the softener was still in the tray and the clothes were wet. I tried to start a new cycle and the water will will come in for a few seconds and then shuts off. That is all that the washer will do. The lights are all on, the tray is closed, and the door is closed.
We checked the hoses and there were no kinks.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kenmore Master
  • 83,481 Answers

Try unplugging the washer for 5 min's and see if it resets, if not call for service.

Posted on Jul 06, 2017

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 1,830 Answers

Do you still have your owner's manual that came with the Kenmore washer? Look under troubleshooting your Kenmore washer.

Posted on Jul 06, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 32 Answers

SOURCE: Softener tray filling with water

open the dispenser all the way,place your finger towards the back left of dispenser.you should see a tab,depress the tab and pull entire dispenser cup out.the bleach and fab soft part of the disp has a removable tray.clean all pieces out including the long shafts on the insert.you will more than likely find a build up of softener,this breaks the siphon and does not allow the water to drain out.good luck

Posted on Sep 28, 2008

  • 1028 Answers

SOURCE: Kenmore washer 24622300. clothes are very wet after spin cycle

washer may not be spining at all start in rinse cycle allow washer to wash and advance through cycle on it's own do not advance manually..after agitation listen for short pause after pause pump out should begin after pump out should be another short pause then spin should start..if spin does not start after 2nd pause suspect transmission if lid is raised spin may start but if it doesn't start during normal operation bad gearcase one other ck possible look underneath for oil it may be getting on clutch causing clutch to slip and not allow to spin full speed

Posted on Nov 21, 2008

  • 77 Answers

SOURCE: Black marks on clothing

hi, i think you will find the bearing on the drum is about to fail, you need to replace it, hope this helps


Posted on Feb 10, 2009

  • 38 Answers

SOURCE: kenmore 44082 washer won't take in fabric softener

Remove hoses from fill valve, clean screens inside fill valve, if this does not fix problem, replace valve.

Posted on Mar 08, 2009

  • 120 Answers

SOURCE: Kenmore washing machine model 110 wash cycle stops

DOES IT DO THIS ON EVERY WASH OR SOMETIMES? IF SOMETIMES, CHECK LID SWITCH( THERE'S A LITTLE HOLE WHEN YOU OPEN THE LID, ON THE LID SHOULD HAVE A LITTLE PLASTIC PIECE THAT GOES IN THAT HOLE. THE SWITCH IS UNDER, INSIDE THAT HOLE. YOU CAN GET A PEN OR KEY TO SEE IF IT'S BROKEN.)
\
BOYNISMO@YAHOO.COM

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

GE GFWS3500LOWW not starting on any cycle


GE Washing Machine GFWS3500L0WW Troubleshooting ...

www.repairclinic.com/...-/GE-Washing-Machine-GFWS3500L0WW-Tr...
GE Washing Machine GFWS3500L0WW ... Washer fills slowly · Washer leaking water · Washer won't start · Washer won't spin or agitate · Washer overflowing ...
Repair Help - Model Help Repairwww.searspartsdirect.com/ge/washer/model-gfws3500l0ww-repair.htmlRepair Symptoms for GE Washer Model #gfws3500l0ww. Shop Parts ... Slow or noagitation or spinning ... Not working at all ... Clean Washer cycle won't work.GE front load washer door latch Repairwww.appliance-repair-it.com/front-load-washer.htmlIf your GE front load washer has a door latch problem such as the door will not lock or... You should always use HE detergent on any front load washer. ... manually unlocking the door and pouring cold water into the tub then start a new cycle.GE Front Load Washer Service modewww.appliance-repair-it.com/GE-front-load-washer.html

Jan 28, 2016 | GE Washing Machines

1 Answer

Why does a Kenmore washer not finish the cycle?


Washer Repair - Not Advancing -Repair & Diagnostic ...

? 8:30
https://www.youtube.com/watch?v=IEr9A7uhdN8
Sep 6, 2013 - Uploaded by ApplianceVideo.com
Repair your Kenmore Top Load Washer suffering from these following issues: Will Not Advance Past Rinse ...

Kenmore washer doesn't complete final spin cycle - ApplianceBlog

www.applianceblog.com/.../31894-Kenmore-washer-doesn-t-complete-fi...
May 16, 2012 - 9 posts - ‎2 authors hello, my kenmore washer doesn't complete the final spin cycle. i ... Does it stop in the middle of the final spin cycle or does it not go into the ... FIXED Kenmore Washer - Not finishing the spin cycle
9 posts
Dec 20, 2014
FIXED Washing Machine Does Not Complete Cycle ...
10 posts
Mar 14, 2013
FIXED Kenmore washer won't spin out all water from ...
10 posts
Jun 27, 2009
FIXED GE front load washer WCVH6260F0WW stops ...
10 posts
Jul 2, 2007
More results from www.applianceblog.com

Nov 05, 2015 | Kenmore Washing Machines

1 Answer

Kenmore Model 22722 will not drain


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Jun 01, 2010 | Washing Machines

1 Answer

My front load Kenmore washer 44082 does not start. just buzzes and displays ERR.


LOC means it thinks the control panel is locked.
This gives the ERR indication when you push the buttons.
To unlock it you need to hold down the Options and Select buttons together until it reacts.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Nov 04, 2009 | Kenmore 44042 Front Load Washer

1 Answer

I'm getting an F26 code on a Kenmore Elite he5t front load washer


DOOR SWITCH ERROR

If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds.

Possible Causes/Procedure

-Door not opened during 3 consecutive cycles.

1. Open and close the door.
2. Verify CCU operation by running a Diagnostic Test or any cycle.

-Door switch open while door is locked.

1. Push the door and check if it is completely closed.
2. Verify CCU operation by running a Diagnostic Test or any cycle.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.!!!!

Oct 31, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Takes almost 2 hours to complete a wash cycle


Have you ever cleaned it out? Its likely due to a plugged drain, not allowing the system to drain fast enough for the normal cycle. Check out my solution on
http://www.fixya.com/support/t114322-kenmore_elite_h3t_washer

-Todd

Mar 30, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

*&^% screws!!!


F2 = Long Drain. Most common cause is something (or lots of things) stuck in the drain pump. There are screws at the bottom of the front panel that can be removed to check it out. If the screws look like stars they are Torx head screws, get driver from most home centers.

Go here for Kenmore HE3 washer parts:
http://www.repairclinic.com/Kenmore-Washing-Machine-Parts

www.RepairClinic.com

Feb 03, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore 44082 washer won't take in fabric softener


Remove hoses from fill valve, clean screens inside fill valve, if this does not fix problem, replace valve.

Jan 17, 2009 | Kenmore 44102 Front Load Washer

1 Answer

Kenmore 44082 front washer will not drain or fill


e23 is not a valid code.
Please re-check and post if you still need help.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 09, 2009 | Kenmore Energy Star 44092 Front Load...

3 Answers

My kenmore 417.42042100 model front loading washer is making a loud banging noise during the spin cycle.


Here's what the problem is. 
http://www.youtube.com/watch?v=UwpKP_9_fAA&feature=player_embedded

It's been designed to fail so that you buy an expensive part. 

Nov 26, 2008 | Kenmore 46462 Front Load Washer

Not finding what you are looking for?
Kenmore 44102 Front Load Washer Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

fordexpert

Level 3 Expert

5690 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

2005 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...