Question about JBL 5.1-Channel Home Theater Speaker System with 150W Subwoofer

1 Answer

Connection system i have taken new 5.1 home theater of jbl model sc140 , and avr of harman kardon company of model avr 133,but i am unable to the system.How to connect.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Hi,
connect satelite speakers to the amplifier and connect signal cable (RC pin) to the woofer from amplifer ie subwoofer out from amp. ok na.

-kanny
kanny-sounds.blogspot.com

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jbl flip does not take a charge


that's because they aren't made to repair just buy a new one

Apr 27, 2015 | Harman Kardon JBL Flip black

1 Answer

Jbl flip instructions


Either pair it through Bluetooth pairing, or use NFC (near field communications) if both devices have it.

All this is detailed in the instructions.

Aug 25, 2014 | Harman Kardon JBL Flip black

1 Answer

JBL flip only plays while connecting to the mains


Seems the battery has gone bad prematurely. Charging circuits have to be good since the unit works fine off the adapter plugged into the mains.

Mar 31, 2014 | Harman Kardon JBL Flip black

2 Answers

JBL Flip blinking red and blue


This indicates that the Blue tooth pairing with the already paired device has been reset and the JBL Flip is ready for pairing with new device. This position, red and blue blinking, can be obtained by long pressing the power buton.

Mar 03, 2013 | Harman Kardon JBL Flip black

3 Answers

Jbl flip does not connect by bluetooth


Press and hold power button while trying to connect to new device to reset conmection

Dec 27, 2012 | Harman Kardon JBL Flip black

1 Answer

I have a KLH ASW10-125C Subwoofer and a Harman Kardon AVR 3600 receiver. What should the setting be for volume, phase and crossover frequency?


Home Theater

volume - personal taste - usually just high enough that you notice the bass - try turning down until you don't notice it then turn up one notch in the switch

phase - depends on distance from other speakers - try initially setting to 0 degrees

cross-over frequency - depends on your other speakers - try setting at 60-100Hz

Nov 09, 2010 | KLH ASW10-125C Subwoofer

1 Answer

I want dimensions of speakers &woofer of model hcs200 but i didnt find on any site of JBL &specs for speakers set & avr134. the entire model no is HCS200.5...


http://www.harmankardon.com/EN-GB/Products/Pages/ProductDetails.aspx?PID=HS%20200/230&accT=1&tsT=0&ovT=0

If this link does not work just look up harmankardon.com where you are

Hope this helps
Thanks for using FixYa


Aug 09, 2010 | JBL 5.1-Channel Home Theater Speaker...

1 Answer

Connection between harmon receiver and A-bus in wall speakers...


There is a CAT5/RJ45 A-Bus interface on the back of the HK AVR 435. That needs to connect to your A-BUS "hub". HK has two hub products: ABH-4000 and ABH-4 (older). Then CAT5 cable can be run from this hub to Wall-installed room-specific controls. HK has the AB-2 product, but any ABus compatible wall control will work. From the wall control, you wire regular audio cable to the speakers. So, some of the questions/issues to solve are: where do the existing wires go that are connected to the in-wall speakers? Typically that location is where to place your in-wall volume and source controls. Then the CAT5 gets wired from those controls back to the hub. And all that's required is a single CAT5 from the AVR to the Hub.

Apr 04, 2009 | Audio Players & Recorders

Not finding what you are looking for?
JBL 5.1-Channel Home Theater Speaker System with 150W Subwoofer Logo

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top JBL Audio Players & Recorders Experts

Michael Edwards
Michael Edwards

Level 1 Expert

53 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a JBL Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...