Question about Washing Machines

1 Answer

Replacing the mother board on my LG machine washing

Can you perhaps supply me with written instructions on how to replace the mother board on my LG washing machine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Disconnect power remove screw from back holding down top,slide top towards back. control panel is located on left rear of cabinet. remove 1 screw on back which hold panel in place. panel will side to inside to release from cabinet , pry open cover disconnect all connections (all connectors are color coded and are diffrent sizes)reverse process. hope this helps

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front loader. Why isn't display working?


If there is mains supply reaching the main power PC board, then the board needs replacing.
Otherwise check the fuses and inline protection systems in order for the supply power to reach the electronics.

Nov 17, 2015 | LG Washing Machines

1 Answer

MY PANASONIC WASHING MACHINE ID DEAD NO POWER INDICATION,NO DISPLAY AFTER PRESSING ON/OFF NO RESPONE,BUT WALL OUTLET POWER IS HEALTHY


this is a modern machine and has a digital controller/display

so the low voltage supply circuit usually on the controller board has failed
usualy caused by water or a short or something come loose

check all connections
i feer youll perhaps need to replace the controller board
too be sure of a good lasting repair
this is what i would do then i would fix the older one and return to stock doing any firmware updates to it also

Dec 01, 2014 | Washing Machines

1 Answer

How to get top off to get acess to replace motherboard?


Make sure that all the screws are out of the back panel. Then the top control plate screws come out. Lastly the top then should just pop off.

Jun 20, 2014 | Whirlpool WTW4950XW Washer

1 Answer

No power for lg wm2277hw


Power supply has failed to the panel board and it can due to failure of the board, failure of the surge filter or the power circuit.
check the panel and if there is short within the board then the panel must be replaced

Jan 16, 2013 | LG WM-2277HW Front Load Washer

1 Answer

Replace main control board of lg front load washing machine


Try this video, please:

http://www.youtube.com/watch?v=z88WwrhlvXw

Jan 16, 2013 | LG Washing Machines

1 Answer

Replace fisher paykel iwl 16 mother board with gwl 11 motherboard


I cannot find your mothers IWL16 model, but I have found various similar machines that are the same phase as your GWL11 machine, the electronics in there although different are compatible, you can swap the drain pumps, there almost universal, avoid the drive shaft machine, fix the other one If you want further help, post a photo of both pcb's (the electronics) After swapping your machine will stil require programming which is simple enough

Sep 14, 2012 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Amica Mother board has been stopped working. its not spinning.


If the board is malfunctioning, your only source of action is to replace it.

May 24, 2012 | Washing Machines

1 Answer

We have LG FULLY AUTOMATIC WASHING MACHINE MODEL NO. 8018LS 7.0 kg PURCHASED 4-5 YEARS BACK. SUDDENLY TODAY WE GOT SOME PROBLEM IN WASHING MACHINE AS "dE" written on the top of the screen. please...


Door switch fault, either replace door switch required or maybe an adjustment of the switch. Push against door inwards when displaying dE and hold pushed in to see if it goes away to confirm switch problem

Aug 29, 2010 | LG Washing Machines

1 Answer

LG WASHER WON'T Power on


Hello. If the lid switch is defective, your washer may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washer to get to the switch. If it's defective, you need to replace it. Some machines have a special lid-switch fuse near the lid switch, inside the control panel. If this fuse blows, the unit won't fill with water until you replace the fuse.

May 24, 2010 | LG WM1814CW Front Load Washer

1 Answer

I have LG washer & dryer 8 / 5 kg WD-14440RDS I could not start it its connect to electrical supply but after we washed clothes yesterday today we could not start??


Does it turn on? if so either the start button is faulty(LG will want to sell the whole board but the switch is fairly easy to replace) or the door lock.

Apr 17, 2010 | LG Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...