Question about HP Officejet 5610 All-In-One InkJet Printer

1 Answer

HP Solution Center won't start automatically when a doc is loaded

I am trying to finish the setup of an HP 5610 on a Widows XP laptop, it used to automatically launch th HP Solution center when a document was loaded in the top tray, now it will not. The Automatically show the HP Solution Center - will not start even if the auto start settings are checked, any Ideas?

Posted by on

  • Anonymous Feb 21, 2009

    HP Solution center won't open, anytime!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Dedicated:

    Visited the website for 20 consecutive days.

  • Master
  • 344 Answers

It appears their are issues with HPSC in newer OSs:

https://support.hp.com/us-en/document/c04740294

I'm not sure if HP is even supporting HPSC anymore. Perhaps you can use this instead (appears to be HP's new one):

https://www.microsoft.com/en-us/store/p/hp-scan-and-capture/9wzdncrfhwl0

I would also have to recommend that you not use Windows XP anymore as Microsoft has not supported it since April 2014. Good luck.

Posted on Jan 16, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
cdhardy
  • 111 Answers

SOURCE: printer is not taking paper from tray automatically

reset to fatory defalt.

Posted on May 29, 2006

Soulvisitor
  • 1113 Answers

SOURCE: tray 1- load plain letter

Linda,

On printer check media/paper type tray 2 or 3 is plain and tray 2/3 is set for letter paper size too, via printer control panel. Also check under paper handling other options for tray 1, also on tray 2 and 3, I think there is a blue little round switch on left should be set as letter not custom.

Some paper types cannot be feed from anywhere else but tray1/bypass ie labels/laminate/card stock.

Check print driver on pc has tray 3 option installed and is not set as default to print to manual bypass/tray 1

light flashing cause printer wants paper type/size that it "thinks" it hasn't got in tray 2/3

If that dont cover it...post back

Soulvisitor :-)

Posted on Dec 18, 2007

SOURCE: HP LaserJet 2840 Scanner problem

Yes, but I don't see any actual paper jams. I have a Vista O/S and I've been reading that that might be the problem; the 2840 scanner driver is not compatible with the Vista O/S and HP hasn't produced a solution yet. I appreciate your efforts, thanks.

Posted on Feb 10, 2008

  • 1894 Answers

SOURCE: Problem with scanning both from the auto feeder and from scanner glass

this is what HP has to say

This document applies to all HP product models. Issue When the product is turned on or in the middle of an operation, an unexpected noise occurs, such as clicking, thumping, or grinding. Blinking lights and error codes might accompany the noise. NOTE: Noises can be caused by a number of things. This document focuses on isolating, identifying, and resolving known causes of product noises. Solution Noises are subjective and can be difficult to describe. Some noises are normal to the operation of the product and might include the following:

  • The product might make humming and buzzing sounds as the carriage moves around on the right or left side of the product while cleaning the ink cartridges. This is normal when a product is turned on, before and after printing, after a product has been on standby for some time, after replacing an ink cartridge, or in the middle of a large print job.
  • During a print job, the movement of rollers, gears, carriage, and paper (paper feed and ejection) creates some noise.
  • During a print job, if the product is printing in the fast or draft mode, the noise level might be higher than when using the best or normal mode.
  • At the end of the print job, a louder clicking noise occurs as the paper is pushed to the output tray.
  • At the end of a print job, a noise emanates from the left or right side of the product as the pens are capped. The product might try to do this a couple of times.
Abnormal noises are a symptom of a problem. The most accurate way to determine the origin of a noise is to isolate where it comes from and when it occurs. Use the following steps to try to isolate the noise issue. NOTE: Error codes might indicate the source of the noise. Make a note of any error code or blinking lights that appear. Step one: Check for loose or broken parts
  1. Raise the cover of the product.
  1. Check inside for loose or broken parts.
  2. If there are broken parts, the product needs to be serviced.
  3. Step two: Make sure that accessories are installed correctly
  1. Press the power button (c00636182.gif ) to turn off the product.
  2. Remove the power cord from the back of the product and unplug the power cord from the power source.
  3. Check any accessories (duplexer, envelope feeder, automatic document feeder (ADF)) to make sure each is installed and seated correctly.
  4. Plug the power cord into the back of the product and plug the power cord back into the power source.
  5. Press the power button (c00636182.gif ) to turn on the product.
  6. If the noise still persists, remove each accessory one at a time to try to determine if the noise is associated with a single accessory or a combination.
  7. If the noise stops when a specific accessory is removed, that part might need to be replaced. If possible, exchange the accessory with a known good one or a new one to determine if the noise is associated with the accessory. NOTE: If the product is fully functional with the accessory in place, the noise might be normal.
  8. If the noise persists, proceed to the next step.
Step three: Check connection with computer Turn off the computer to determine if the computer is the source of the noise. If the noise persists, proceed to Step four. If the noise stops when the computer is turned off, try to isolate any issues with connectivity:
  1. Press the power button (c00636182.gif ) to turn off the product.
  2. Disconnect the USB cable from the product.
  3. Unplug the power cord from the wall outlet and from the back of the product.
  4. Wait a couple of minutes to allow static to be discharged.
  5. Plug the power cord into the wall outlet and plug the power cord into the back of the product.
  6. Connect the product to a different USB port.
  7. Turn on the computer.
  8. Press the power button (c00636182.gif ) to turn on the product.
  9. If the noise persists, service the product.
Step four: Check for a paper jam Paper jams can prevent the internal components of the product from moving, which can create unusual noises.
  1. Press the power button (c00636182.gif ) to turn off the product.
  2. Disconnect the power cord from the back of the product.
  3. Remove the rear access door.
  4. Remove any paper that is inside the product by pulling it out through the rear access door and then securely replace the rear access door.
    1. If a paper jam cannot be removed from the back of the product, raise the product cover, carefully remove the paper jam from the front of the product, and then lower the cover.
    NOTE: Remove any paper jam carefully as it is possible to damage the product when removing a jam from the front of the product.
    1. Reconnect the power cord to the back of the product.
    2. Reload the paper in the paper tray.
    3. Press the power button (c00636182.gif ) to turn on the product.
    4. Try to print. If a jam is cleared and the product prints, but the noise persists, proceed to the next step.
    5. Step five: Make sure that the carriage moves freely
    1. Press the power button (c00636182.gif ) to turn off the product.
    2. Disconnect the power cord from the product.

    1. Make sure that the ink cartridges are locked into the carriage and have not come loose. Also make sure that there are no obstructions under or around the carriage to prevent it from moving.
    2. Close the product cover and reconnect the power cord.
    3. Press the power button (c00636182.gif ) to turn on the product.
    4. If the noise persists, proceed to the next step.
    5. Step six: Plug the product into a wall outlet
    If the product is plugged into an uninterruptible power supply, that source might make a beeping or whistling noise.
    1. Unplug the power cord from any power strips or surge protectors.
    2. Plug the power cord directly into a wall outlet instead.
    3. Press the power button (c00636182.gif ) to turn on the product. If the noise persists, proceed to the next step. If the noise stops when plugged directly into a wall outlet, the power strip or surge protector might not be allowing sufficient voltage to reach the product and might need to be replaced.
    Step eight: Service the product If you have completed all the steps listed above and are still experiencing a problem, service the product.

    Comments by scrodamoon in premium

    Posted on Aug 05, 2008

    Riztech
    • 731 Answers

    SOURCE: HP Solution Center No HP Devices Detected

    Try this

    1.Right click on MY computer ->Properties->Hardware->Device manager.

    2.You will get Device manager window popping out.

    3.Scroll down to "Universal Serial BUS controllers".Click on the (+) sign.

    4.Check for the "USB Composite Device" and right click on it, click Uninstall.(IMPORTANT NOTE:wE HAVE TO UNINSTALL THE PRINTER'S USB COMPOSITE DEVICE, TO KNOW WHETHER IS THE PRINTER'S USB COMPOSITE DEVICE, RIGHT CLICK ON USB COMPOSITE DEVICE AND PROPERTIES,look for wat location says, Eg -LOCATION : HP DESKJET F2100

    5.Disconnect the USB and reboot the PC.

    6.Connect the USB after reboot, you will get popup "Found new hardware".Then the Drivers will be installed Automatically.

    Thanks
    Riz

    Posted on Jan 08, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    External volume key doesn't work


    Did you install the system board drivers from acer?

    Mar 06, 2014 | Acer Aspire 5610-4648 Notebook

    1 Answer

    I am using sony vaio sve15113enw model and it doesn't start automatically on starting my laptop i have to press any of the button after pressing the power button then only the windows will load. pleas


    pls go to the bios setup by tapping F8 or F10 while starting up and then reset the bios to default settings.....if that helps good if not then pls revert back

    Dec 27, 2013 | Sony VAIO PCG-K35 Notebook

    2 Answers

    Hi, I'm installing widows xp in HP Compaq nc6220, but after setup loading files the mesaage (bottom of setup screen) "Setup is starting windows", then it did'nt contiue the installation,...


    1 many times the the CD cant load as the files in the CD are corrupt or the CD is not read by the drive corectly...so get a new WinXP CD
    2 try an external CD drive if your BIOS alows to boot from USB drive....(connect the external CD drive to the USB and make necessary changes to the BIOS boot seq in the BIOS screen...
    BIOS screen can be enabled by pressing the F1, or F2 or the Del key as on as you start the PC
    3 once in BIOS screen look for boot seq and change the boot drive to the foll
    1st boot device - USB CD / DVD rom drive
    2nd boot device - internal CD rom drive
    and so on

    if you can do the above then try the WinXP installation using the external CD rom drive....
    else there is a little complicated method of using a pen drive thru USB (will discuss that later) provided your BIOS alows booting from USB

    for more PC related issues visit my website
    reg
    kris
    suresh_krishnan1961@yahoo.com

    www.sureshayyar.110mb.com

    May 18, 2011 | HP Compaq nc6220 Notebook

    1 Answer

    Can not start the Windows after reinstaling it


    Try to clean up your cd recovery, maybe some file cannot copy while installing.
    tips: don't clean cd with circle direction, just wipe straight direction from center to outer cd for better result.

    hope this will help you.

    Jun 07, 2009 | Acer Aspire 1714SMI Notebook

    1 Answer

    Widows XP


    (1) go to Hp.com - load load the necessary Xp drivers for your unit - burn them to cd - then aquire a replacement hdd - install Xp on that - install the required drivers and walla you have one hdd with vista and another with XP

    Jan 21, 2009 | HP Compaq 6720s PC Notebook

    1 Answer

    Hp officejet 5610


    There might be some issues either with the printer cable or the USB port on your system... Just try another cable if you have one... or u can also try another usb port on the system...

    Jan 03, 2009 | HP Officejet 5610 All-In-One InkJet...

    4 Answers

    I do not have the CD to install it


    You can download the drivers for your printer from HP HERE

    You can also get user manuals and setup instructions.

    Sep 13, 2008 | HP Officejet 5610 All-In-One InkJet...

    2 Answers

    Hp 2210 allinone


    I just went through this with HP tech. Seems this is an known problem and their solution is for you to purchase a refurbished or new printer from them which happens to be more than you can purchase online.

    You can try taking a lint free cloth, popping out your cartridges and briskly rubbing the copper and ink nozzle part of the cartridges to see if that works. Also briskly rub the connections inside the printer itself where the cartirdges make contact. If this doesn't work then you now have a HP paperweight.

    I haven't had any luck with HP printers. Always something goofy going wrong. Software gets corrupt, update can't update, won't print, etc... I purchased this thing new and had to return it the first week for a replacement because it wouldn't power on.

    I'm going to another brand. Possibly Cannon or Epson and hope for the best. Anyway good luck!

    Aug 22, 2008 | HP Officejet 5610 All-In-One InkJet...

    2 Answers

    Cannot scan via 5610 because the screen message refers to microsoft word


    Hi,

    If you are trying to scan a document, and the settings that you have on the HP SOlution Center Installed in your computer uses the Microsoft Word as SCAN TO, you cant use it since your Microsoft Word Office is not yet setup. You may try using the WOrd Pad instead. Or, you can use the .pdf to scan a document. Just open the SOlution Center on your computer, and try to go to click on Scan Documents- the window will pop-up and change some settings there.

    Thank you so much.

    adonscott

    Jul 22, 2008 | HP Officejet 5610 All-In-One InkJet...

    2 Answers

    Installing widows XP


    first, have a WIN XP startup disk...created by (in windows)  inserting floppy and right clicking choosing format and select option "create MSDOS startup disk"

    first backup all personal files...then restart and bypass to DOS screen at startup...try using F8 key just after BIOS screen...then select startup to DOS prompt only...then run (from the floppy disc) format c:

    now you should have a nearly bare hard drive. repeat above steps and this time choose "startup using CDROM drivers"...then insert CDROM and redirect to that drive letter (d drive?) and run setup.exe.

    Oct 30, 2007 | Compaq Presario C552US Notebook PC

    Not finding what you are looking for?
    HP Officejet 5610 All-In-One InkJet Printer Logo

    Related Topics:

    352 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Office Equipment & Supplies Experts

    mukhtar21 shaikh
    mukhtar21 shaikh

    Level 3 Expert

    2022 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18425 Answers

    Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...