Question about Blueant Supertooth Light Bluetooth Speaker Car Kit

1 Answer

Just bought a iPhone 3G and i have a BlueAnt Supertooth light and the iPhone isn't discovering it...help?

Posted by on

  • Anonymous Jan 17, 2009

    I upgraded my iPhone 2g to 2.2 Sw version, now ST Light does not work anymore.....

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 827 Answers

Try following the below instructions, if you haven't already tried them..

First Time Pairing to your Bluetooth Mobile Phone
When you turn ON your Supertooth Light for the first time, it will automatically go into Pairing mode ready to be found by devices in Bluetooth searches. This will be the case until you have successfully paired a phone. If you have already paired a
phone, please go to the next section.
1. Power ON your Supertooth Light. The Bluetooth Indicator (3) will turn a blinking
red/blue, The kit is now in pairing mode.
2. Go to Point 3 in the next section, “Pairing to your Bluetooth Mobile phone”

Pairing to your Bluetooth Mobile Phone
Pair the SUPERTOOTH LIGHT to your Bluetooth mobile phone to create a “Pairing”
link, or audio connection between the two. This has to be only done once when first connecting each new phone.
1. From OFF, Press and Hold the Accept Button (1).
2. While holding the Accept Button (1), switch the kit on (Press-and-release the
Microphone Shaft (5)).
3. The Bluetooth Indicator (3) will turn a blinking red/blue, when you see
this, release the Accept Button (1). The kit is now in pairing mode.
4. While the kit is in pairing mode, access the Bluetooth menu of your phone. Turn on the Bluetooth function then execute a Bluetooth search, or discover. (See your phone’s manual for specific instructions.)
5. When the phone displays the list of Bluetooth devices, select ST LIGHT.
6. When the phone asks for the password, enter 0000 and press Ok.
7. Set the ST LIGHT as a trusted/authorized device, if this is option in your phone.
Important Note: The kit is now paired. Most phones automatically connect to the
kit after pairing. With some phones you need to connect manually after pairing.
Go back to Bluetooth > Paired devices > highlight ST LIGHT > press
Options > then press Connect.
When connected you may see the Bluetooth Symbol on your phone change
slightly, either inverting in color or changing to a headset or car symbol. The kit
is now ready to use.
Repeat steps 1 -7 above for each new phone you want to use with the
Supertooth Light.

This was copied from the user manual, which you may or may not have already.. Here's a link to a .pdf file of the manual which you can also save to your computer:

http://www.blueantwireless.com/downloads/supertooth_light/supertooth_light_manual.pdf

Hope this helps :)
Season's Greetings!

Chris (ziraffa)

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you pair an iPhone with the blueAnt st3?


Step 1: Activate Pairing Mode on the Supertooth 3

Make sure the Supertooth 3 is turned off.
You can tell if the Supertooth 3 is on or off by looking at the light on the front. If the light is on or flashing, then the Supertooth 3 is on: turn it off by holding down the Multi-Function button (the green button) for about 5 seconds, until you hear the voice announce that the Supertooth 3 is powering down.
With the Supertooth 3 off, hold down the Multi-Function button for about 6 seconds, until the light on the front of the unit starts flashing red and blue.
The Supertooth 3 will now prompt you to select your language: press the Multi-Function button when you hear your language spoken.
The Supertooth 3 is now in pairing mode.


Step 2: Apple iPhone

Now you need to use your iPhone to search for Bluetooth devices:

Select Settings.
Select General.
Select Bluetooth.
Wait for your phone to search for devices, then select your BlueAnt device from the list.
If you are prompted for a PIN, enter 0000 (four zeros).
Select Connect.

Your BlueAnt device is now paired.

Jul 12, 2011 | Blueant Supertooth 3 Bluetooth Handsfree...

1 Answer

How do i coinnect my blueant supertooth to my iPhone 4


Make sure you have the most up-to-date firmware version. (Currently 1.6 in the United States). A full tutorial on how to connection Blue Ant Super tooth 3 to any Bluetooth interface is listed here. (Tward the bottom of the page, you can get the firmware updates at the top.)


Apple also offers a direct howto section on the iPhone 4 and how to pair it to bluetooth devices. Here.
Hope this solution helps you. If so please recommend it and rate it! :)

Jan 12, 2011 | Blueant Supertooth Light Bluetooth Speaker...

2 Answers

I have a BlueAnt Supertooth BTSLBC3 car speaker that won't pair up to my new BlackBerry curve 8530 phone. The BlackBerry won't see the BlueAnt Supertooth BTSLBC3. The BlueAnt Supertooth BTSLBC3 is paired...


Pairing Your BlueAntStep 2: Activate Pairing Mode on the Supertooth Light
  1. If the microphone arm is open, close it to turn the Supertooth Light off.
  2. Press and hold the answer button.
  3. With the answer button held down, open the microphone arm.
  4. The lights will start flashing red and blue, indicating that the Supertooth Light is in pairing mode.
You now need to activate Bluetooth

Apr 03, 2010 | Blueant Supertooth Light Bluetooth Speaker...

1 Answer

I need to pair the BlueAnt to a new iphone


BlueAnt has a website that tells you step by step how to pair. I followed it and was successful. Thank you for your interest.

Nov 10, 2009 | Blueant Supertooth Light Bluetooth Speaker...

1 Answer

BlueAnt Supertooth Light wll not connect to apple iphone When I switched to a iphone 3gs it will recognize the devise but when I place the code in which is ''0000'' it says the pin in invalid.


Go to this page, it will answer any question concerning the blueant .. including pairing to your phone .. activating your blueant etc http://www.blueant.com.au/index.phpalso gives you step by step instructions on codes, pairing etc

Jul 08, 2009 | Blueant Supertooth Light Bluetooth...

1 Answer

How do i sync supertooth light to a new mobile phone


Turn the blueant off by holding the green button until it powers down. Put your phone in discover mode (refer to your phone's manual) then power the blueant back up but hold down the green button until the light starts flashing red and blue. Now you should be able to see it on the phone. I just discovered my Samsung I910 wouldn't pair unless I used the windows on screen keyboard instead of the Samsung on screen keyboard.

Jun 11, 2009 | Blueant Supertooth Light Bluetooth Speaker...

3 Answers

My g3 iphone says blue ant st3 password incorrect but it's the only one they give you...won't connect with my phone


Hi - I had the same problem setting up my 3G S. Here's the solution. In "Settings/General" set the Bluetooth to "ON". Turn your ST3 OFF by holding the green button until she says it's Powering Down. Now press and hold the green button ON until Language Selection (British English) option. Select language by pressing green button again. Next she will say "Device Found-Paring Successful-Enter password 0000". Enter 0000 and your phonebook will start downloading. There ya go!

Jun 07, 2009 | Blueant Blue Ant 091193 Supertooth II...

1 Answer

BlueAnt does not seem to discover my Pantech C520 cell phone. Can u help?


is your bluetooth turned on on your phone? and make sure its in discover mode

May 05, 2009 | Blueant Supertooth Light Bluetooth Speaker...

Not finding what you are looking for?
Blueant Supertooth Light Bluetooth Speaker Car Kit Logo

841 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blueant Radio Communications Experts

Iron
Iron

Level 3 Expert

3018 Answers

aliasger yq

Level 2 Expert

213 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Blueant Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...