Question about Ryobi 26CC, 22 In. Hedge Trimmer

1 Answer

Purchase of Ryobi RTB510 carbon brushes

The bruhes in my hedger have worn down to the holder and are now arcing badly, sometimes stopping all together.
I live in the Sutherland Shire out of Sydney & would like to purchase a new set of brushes.

Posted by on

  • Mark Tripp
    Mark Tripp May 11, 2010

    what is the model and serial numberof your hedge trimmer and I will see wat I can find for you

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 76 Answers

You can go directly thru ryobi at www.ryobi.com they can help you get the parts you need.

Posted on Mar 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Replacement carbon brushes Ryobi AG402 angle grinder


You can purchase replacement carbon brushes on amazon Amazon com Ryobi carbon brushes. I hope this was helpful. cheers

Jul 12, 2013 | Saws

1 Answer

Rear wheel sticks and sometimes when you go to go forward nothing l of a happens,then al of a sudden it jurks forward with no warning.l


Hi. Sounds like you have worn out motor brushes. the brushes wear down to short and get stuck in the brush holders. Sometimes the caps that hold the carbon brushes in come loose, and the carbon brushes get stuck because the current arcs between the carbon brush and the brush guide. Get a serviceman to overhaul the motor, and it will work fine. Probably a good idea to replace the motor bearings at the same time. Good luck. Neil.

May 27, 2010 | Pride New Mobility Legend 4 Wheel Scooter

1 Answer

I have a Ryobi RE175. It just stopped working


1. Shut the power off, and disconnect your Ryobi
router. It could be the start/stop switch. So, you
can begin checking the switch contacts using the
multi-tester. Set if at 1 x 10 Ohms. Put the probes
of the tester across the switch terminals. Pressing
the trigger on will move the tester indicator to zero
if your switch is okey. Otherwise, no moverment -
the trigger switch need replacement.
2. Should the trigger switch proved to be okey, Check
the carbon brush of the unit, short carbon brush??
you have to replace it.

Nov 03, 2009 | Electrical Supplies

1 Answer

Rear pass window does not close solonoid clicks no load on lights


Then power is not reaching the motor ie bad connection past relay or the motor is toast, worn so badly theirs no connection through brushes. Some times just dirty or carbon build up. Low voltage is usually the culprit, running accessories like these without the engine running or with a weak battery can result in excessive heat and arcing can occur causing carbon deposits making contact impossible. Sometime slamming the door will instigate contact and it will run for a bit but the damage is done and repairs from cleaning to replacing are in order.

Jun 20, 2009 | 1999 Lincoln Continental

1 Answer

My Ryobi 10 inch miter saw, model TS 1340 has been working fine for years, now in the last 7 days, I see heavy sparking at the carbon brushes and a drop in power from the saw, there is a strong smell of...


It sounds like the armature has developed an open commutator bar. What did the brushes look like that you took out. But before I assume the worst I would unplug the tool and remove both brushes and with a flas light look into the brush tube while slowly rotating the armature looking for a discoloration or raised bar. If not you might bet by with cleaning the commutator with a special stone for this, you might be able to get one at the repair shop where you bought the brushes. If you want to send me the photo of the arcing it might help on my end. Let me know

Mar 09, 2009 | Ryobi Saws

1 Answer

Bosch wfr2460


hi Many universal motor malfunctions are caused by wearing down of the carbon brushes, the soft blocks of carbon that complete the electrical contact to the motor's commutator. When these brushes become worn, the motor will spark, and electrical contact may be incomplete.try this
Step 1: To sight-check the carbon brushes, remove the screws that hold the brushes and brush springs into the brush holders at the sides of the commutator. The screws will pop out of the screw holes; turn the motor over to tap out the brushes. The ends of the brushes should be curved to fit the commutator; if they're worn down, new brushes are needed.
Step 2: To check carbon brushes with a continuity tester, remove the motor lead wires from the circuit. Tag the wires as you disconnect them so that you'll be able to reconnect them properly. Hook the tester clip to one motor lead and touch the probe to the other lead; the tester should light or buzz. Slowly rotate the motor shaft, keeping the tester in position. If the tester doesn't light or buzz, or if it flickers or stutters when you turn the motor shaft, the brushes should be replaced. If the springs behind the brushes are damaged, they should be replaced as well.

Step 3: Replace worn carbon brushes and damaged springs with new ones made specifically for the motor. The model information (number and make) is stamped on a metal plate fastened to the motor, or embossed on the metal housing of the motor. If you can't find the model information, take the worn brushes and springs with you to an appliance-parts store to make sure you get the right kind. Insert the new springs and brushes in the brush holders, replace the brush assemblies, and secure the new brushes with the mounting screws that held the old brushes.

Sep 13, 2008 | Bosch Axxis+ WFR 2460 Front Load Washer

4 Answers

Heater fan not working


you may have a worn out carbon brushes on the motor.

pull out the motor and replace the brushes...

tnx 4 using fixya,

drcool

Jul 28, 2008 | 1998 Audi A4

1 Answer

AEG Oko Lavamat 86700


check the carbon brushes on the motor as when they are worn arcing occurs and this could trip the electric and the smell could be the plastic brush holders getting hot due to the arcing

Jul 15, 2008 | Washing Machines

2 Answers

Blower for AC/Heater stopped working


if you can reach the blower motor, it could be a worn out carbon brush of the blower motor. if they are, buy a set of carbon brush, learn how to replace them and it would be back running in no time. by the way, when you pull out the carbon brush holder, make sure you dont interchange the position. you can put them back wards and what would happen is the rotation will be reversed. either you reversed the carbon brush holder or just simply interchange the wires that are coming to the motor. i hope i was able to help...

Jul 07, 2008 | 2000 Ford Focus

1 Answer

Wont spin, and arcs.


2 bruhes in motor
replace motor brushes
use correct brushes from bosch

Oct 09, 2007 | Bosch Axxis WFL 2060 Front Load Washer

Not finding what you are looking for?
Ryobi 26CC, 22 In. Hedge Trimmer Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Garden Experts

Nick Olsen

Level 2 Expert

183 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Ryobi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...