Question about Home

1 Answer

AKP957/IX Do you have the above built-under electric double oven operating manual? Thanks Carol

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No. I haven't. Could you email to me? Thanks.

Posted on Dec 15, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Lost manual and do not know how to use my self cleaning oven. It is a whirlpool. (I don't know what model). What do I set oven on and for how long? Please give me some instructions to use the...

On the front of the oven there is a lever.That is the lock.Lock the oven and then set the temp to clean.Some will lock only when the cleaning starts,others need to be locked first.Try it both ways.

Jun 18, 2011 | Home

1 Answer

We have a 200' deep well. The pump is not working and we cant pull the pump up. It has been sujested that we hook a backhoe onto the plastic pipe and wires lift up and pray. Before I do this are there...

I would try to tie off at the fittings and wire at well cap and lift carefully with backhoe a few feet. I would use double line of 1/4 well rope at least 1250 p.s.i. tensile strength. Lift for a few feet ,enough to get access to suction line and wire. Thentie off lines with double x knots and use electrical tape to make several wraps around pipe,ropes, and wire. Use a stainless steel gear clamp to secure everything in place.From that point lift carefully and as straight up as possible and repeat process.
Continue doing this and just go slow and steady. The main thing I would worry about is that depending what type of pipe and fittings were used is that fitting that is connected to pump will break. I know this is a slow process but I have done this several times with good success. If you tie off and secure with gear clamps every few feet and make sure you have the wiring hooked in tightly it will hold a lot of weight as the wire gauge should be at least 10.
Wishing you the best. Thank you.

Feb 24, 2011 | Home

1 Answer

Our jacuzzi is almost regular tub and has tow metal buttons, one on the top/edge and the other near jet mouse at the middle level of bath tub. We have not used our jacuzzi for 10 months. Even we only use...

The metal button on the top of the tub is used to turn the tub on/off. the metal button you see in the middle of the tub above one of the jets is the low water sensor.
the water has to be above that metal tab, you have to be in the tub and then touch the metal button on the top of the tub to turn it on.
this system uses the electrical current from our bodies to complete the circuitry and turn it all on and off.

Feb 12, 2011 | Home

1 Answer

Just moved into new rental property,brand new whirlpool oven, but no manual. Need manual to figure out all the settings in the oven.Model Pro A 80S serie 0839006993.R

I'm not familiar with that series, but you can go to and enter your product information there and it should pull up the needed literature.

Jul 30, 2010 | Home

1 Answer

Jets don't work in the jetted tub.

First the obvious, most are electrically connected to a ground fault device, ether an outlet or a breaker. BEFORE ADDING WATER, check these out to make sure they are not tripped. Most all tubs have a minimum water level which must be reached before the jets will operate. This is usually a piece of trim located above the depth of the jets. Make sure the tub is filled to cover this part. If you cant identify the water level device fill the tub so that all the jets are covered by an inch or 2. Some tubs have push button switches or touch pads to control the motor, some have touch sensitive trim. There may be some sort of medallion from the maker on the tub, simply touching it will start the tub. Once you get it going most tubs have a built in timer that turns off the pump in 15 - 20 minutes. For more tub time just hit the switch again but keep in mind that extended exposure in a hot tub can mess with your blood pressure and cause you to loose balance or pass out, hence the 20 minute timer.

Mar 22, 2010 | Whirlpool Safety Bath Walk In Bathtub -...

1 Answer

On installation have gas coming in through the pipe but no gas gets to the burners. We have verified the gas coming in but do not have anything coming through the oven or the stove burners. I do not have...

You have a gas valve on the unit and once your turn the burner knobs, it opens the valve. Your valve is bad. I have replaced the oven valve on my unit a few years ago. You have to do a voltage check to the valve to see if the valve is being told by the controls to come on. Once you have established that the valve is being called to come on, then you know for sure the valve is bad. Also there is a small gas regulator on the stove near the inlet to it that could be plugged up but I doubt it. Its probably the gas valve which is generally located under the top. Some units have one (like mine) under the oven behind the broiler drawer or pan drawer, depending on what model you have. I hope this doesn't sound crazy, but you did plug the unit in right? It might now be electronic ignition but I wanted to cover everything for you.

Apr 07, 2009 | Whirlpool Home

1 Answer

Electrical installation

From the specs that you are showing 800 watts @ 230 volts will pull under 3.5 amps. I would install a 20 amp 220 volt circuit with #12 wire. Just double check if the tub requires a 3 wire ckt (2 hots & ground) or a 4 wire ckt. ( 2 hots, neutral & ground) Make sure the ckt. is GFCI protected!

Nov 18, 2008 | Home

Not finding what you are looking for?
Home Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Experts

Donni Steen

Level 3 Expert

659 Answers

john h

Level 3 Expert

7409 Answers

Brad Brown

Level 3 Expert

14336 Answers

Are you a Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides