Question about Ford Code-Alarm Code Alarm Transponder

1 Answer

Remote key will not open door - Ford Code-Alarm Code Alarm Transponder

Posted by on

  • jimothyinnot May 11, 2010

    Make, model, year of car, and if aftermarket alarm, what is it?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Hi, gareth hear
i think this mite work 4 u

get in your car and put key in ignition turn 1 turn then wait approx 15 20 secs for light in clock to go red then take key out light should stay lit, next get out of your car close door then lock it and open it, when u open car light in clock should flash 3 times, next get out of car hold lock button on your remote down and push open button 3 times (keeping lock button down and remote pointed at reciver) next lose go of both buttons and red light on key should flash 3 times at the same time as clock inside the car.
next get in your car with key! then start her up and turn off get out of car close door and push button to lock (it should lock) if not get back in start her up again and turn off, then push the door locks inside the car then open get out and your car will lock this time!!!!!!!

this will work 4 u!!!

good luck

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix remote system of Honda City 2006 when remote doesn't open door after replacing batteries?


You should nd to insert ur key in your ignition turn on but do not start the vehicle and hit lock and unlock on controller

Jul 31, 2014 | Vehicle Security Systems

1 Answer

Viper 479V Viper Responder Remote how to program


open the door, turn the key on, press valet switch one time and press it again and hold it until alarm beeps if it dosent beep it means that alarm hasn't read the door open if it beeps press lock on the remote and it should beep again and its will be set. (if the alarm dosent beep you have to put the door trigger wire (green) to ground and repeat steps from beggining

Apr 02, 2014 | Viper 5701 VIPER 5701 2-WAY ALARM w/REMOTE...

1 Answer

How to program 473v remote


Open the door, turn the key on, press valet switch one time and press it again and hold it until alarm beeps if it dosent beep it means that alarm hasn't read the door open if it beeps press lock on the remote and it should beep again and its will be set. (if the alarm dosent beep you have to put the door trigger wire (green) to ground and repeat steps from beggining

Sep 16, 2013 | Viper 5101 LE 1 Way Car Remote Starter...

1 Answer

I need to know the steps ( opening driver door, turnig the key on n' off etc,etc. ) to activated the alarm 4103


The 4103 is not an alarm! It's a keyless entry and remote starter. So...what are you trying to do.

Feb 13, 2013 | Avital 4103LX Remote Start System with Two...

1 Answer

I had an avital 4103 remote start professionaly installed and now then i go to put the key into the ignition it wont start. I have a 2001 chevy trailblazer. The dash flashes security and i leave my key in...


U are probly opening the door then hitting ur doorlock button then shutting the door. The factory system is being armed whwn u loxk the door. Try shutting the door without loxking it. See if ur factory alarm light came on. If that solves ye issue, u need to some minor rewire on ur alarm.

Sep 05, 2012 | Avital 4103LX Remote Start System with Two...

1 Answer

I bought a used car toyota camry 2005 and it has avital key less remote system installed. model is 474L. It has remote start working and drive door open/close However, i am not able to open the power...


The Camry you purchased may not be equipped with a power trunk. Press and hold the trunk button for appoximately 4 seconds. The trunk should release if the wire is connected and, you have a power trunk.
The Camry (and other toyotas) require a double pulse on the unlock wire. If the double pulse is not programmed the aftermarket unit will mimic the factory keyless entry. One press of the unlock button opens the drivers door. Immediately press the unlock button again to unlock the other doors.

May 05, 2011 | Avital 474L TX 4-Button Replacement TX...

1 Answer

Doors only with ignition key


Step 1 Close all of the doors on your car, including the trunk and the hood. Remove your key from the ignition.
  • Step 2 Open the trunk and then get in the car. Close the driver's door and put the key in the ignition.
  • Step 3 Turn the key one click to the right, then back to the off position. Repeat this process quickly five times, ending in the off position. This process must be completed in 10 seconds. If successful, you will hear a beep.
  • Step 4 Open and close your driver's door and press any button on your remote to begin the programming process. The red light on your remote will flash on and off.
  • Step 5 Open your driver's door and get out of the car to close the trunk. Close the driver's door and wait for the keyless remote to emit another short beep. The programming is now complete.



  • make sure you write a review for me ant voet if I was of any help. Thanks Ivan

    Feb 03, 2010 | Vehicle Security Systems

    2 Answers

    Unable to open doors with key due to discharge battery


    you should not have a problem with this as the key is located in the remote and the alerm will sound but as soon as you put the key in the ignition the vehicle cancell the alarm[sword key in the remote

    Jul 21, 2009 | BMW Anti-theft Alarm System 3 Series E90...

    1 Answer

    Remote start 04 quest S


    It will not affect the key. I would suggest python or sidewinder

    Jul 07, 2009 | Vehicle Security Systems

    2 Answers

    2006 Mazda 5 keyless remote fob


    I am a technition for mazda, and if the lights are coming on to the keyfobs, the batteries are fine. What procedure did you follow?
    1. Take key out of ignition
    2. Shut all doors
    3. Open drivers door
    4. Insert key to ignition
    5. Cycle between On & Lock 3 times, leaving key in Lock
    6. Close and open the drivers door 3 times, leaving the door open
    7. The Locks should cycle.
    8. Press the Panic button on the remote twice.

    Jan 31, 2009 | SMC Alarm & Keyless Entry System for Mazda...

    Not finding what you are looking for?
    Ford Code-Alarm Code Alarm  Transponder Logo

    679 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Vehicle Security Systems Experts

    xxxxxx xxx

    Level 3 Expert

    4706 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Larry Spears
    Larry Spears

    Level 3 Expert

    625 Answers

    Are you a Ford Vehicle Security System Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...