Question about Husqvarna "Chain Saw - 16" Bar, 3 Hp

1 Answer

Carburetor problem How to adjust carburetor husqvarna 136?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

Hi

High speed H=3\4 turn

Low speedL=1 1/4 turn

idle speed t adjust accordingly.

regards savumihai71

Posted on Dec 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starts but stalls when hot. Chain is not too tight


Larry,Carburetor may be dirty, remove and clean or rebuild. Check the attached links,videos,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Husqvarna Chainsaw 235Troubleshooting Repair Help

How to Troubleshoot Husqvarna Chainsaw Problems eHow

Husqvarna 136 Chainsaw Carburetor Rebuild Fuel Line Repair

http://www.mymowerparts.com/pdf/Husqvarna-Service-Repair-Manuals/W9200002.pdf

Apr 19, 2016 | Husqvarna Chain Saw Models 51, 55

1 Answer

Have husqvarna 136 runs good but no power when cutting


Three things to check that might be the problem.
  1. Spark arrestor may partially clogged. Located inside the muffler.
  2. Piston and/or cylinder damage. Can be check by removing the whole muffler looking through the port.
  3. Or simply be a carburetor out adjustment.

Dec 24, 2014 | Chainsaws

1 Answer

Husqvarna problems


If spark is ok then I would say the carburetor is the likely problem or the fuel is not entering the engine. Something like the following instructions might help.
How to Adjust Husqvarna Carburetor eHow

Look at this manual for model 51 carburetor adjustments.
http://www.getsaws.com/PDFs/w9600001.pdf

Aug 06, 2014 | Husqvarna Chain Saw Models 51, 55

1 Answer

How do I adjust carb on a 136 husquvarna chainsaw??


If running and you just wish to tweak it a little just follow this. If you need a starting point start at 1 turn CCW from lightly closed then follow this.
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly.
Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.

There are 2 wav (sound - idle & full – may not be highlighted) files that I find most helpful, I think you will too. HTH
Lou
If your description was a little brief and I missed your question reply below and I will get back to you.

Feb 14, 2010 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

2 Answers

Husqvarna 136 chainsaw not starting.


I think your air fuel mixture isn't correct. I think you think that as well. This can be caused by a loose carburetor, cracked fuel lines, dirty air filter, plugged fuel filter, old fuel mix, and a few more things that aren't coming to mind.

If the saw runs lean it will be destroyed. It sounds as though your mechanical abilities are limited, if it's my saw I'd invest $40 in a tune up at the local saw shop (not lawn mower). If you opt for this, ask the mechanic the ratio of the fuel mix he used when making adjustments. Continue using this mix until the next tune up.

If you are bent on attempting to adjust your carburetor repost and someone else will certainly give you a sketchy explanation that may well lead to failure of your saw. HTH
Lou

Sep 23, 2009 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

1 Answer

Husqvarna 136 chainsaw


Both H and L screws should be set 1-1/2 turns out from stop. Turn the idle speed screw two turns in from where it is now. When you had the carburetor apart, did the rubber diaphragm seem hard? If it did, re-kit the unit. When you clean the carburetor body, use spray carburetor cleaner and use compressed air to blow out all fuel passages including the two mixture control screw holes. Be sure to check the condition of the fuel line and the air cleaner. Even a plugged muffler can cause weird problems.

Aug 23, 2009 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

1 Answer

Jonsered 2141chainsaw carburetor adjustment.


You need to set the mixtures for the carburetor. You will find a Low and High adjustment screw. At idle turn the screw in or clockwise until the rps starts to decrease. Then start turning it out till you hit max idle rpms. Turn screw back in a quarter to half turn and it should be idling smoothly. Be careful here and get someone to hold saw if necessary but hold in throttle to full speed and do the same with high adjustment screw. turn it in till rpm starts to drop then back it out until you get to max rpm and it won't go any higher then turn it back in a half a turn.

Jul 08, 2009 | Husqvarna Chainsaws

5 Answers

Husqvarna chainsaw carburetor adjustment


Find the 2 screws. There will be a (h) high and (L) low. These are for hig rpms and low rpms. First tighten the screws. Then unscrew them about 1-1/4 turns. Then start the saw and let it warm up. Start with the high rpms first pull the trigger all the way then adjust the screw in 1/8 turns either way until it is running good at high rpms. Then work on the L rpms. Get the saw to idle then pull the trigger, there should not be any hesitation when going from L to H rpms. Just adjust the low same as the High. They have to work together so if the high is good and the low is not just right turn the h a small amount. If you have any more questions let me know

Jun 11, 2009 | Husqvarna Forest & Garden No.967012396 345...

Not finding what you are looking for?
Husqvarna "Chain Saw - 16" Bar, 3 Hp Logo

935 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Chainsaws Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

Phil Walker
Phil Walker

Level 3 Expert

602 Answers

Are you a Husqvarna Chainsaw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...