Question about GE Profile Spectra JGBP90 Gas Kitchen Range

1 Answer

Constant beeping My oven has been beeping on and off recently and F0 is shown on the control panel. I don't have the manual and so I need help in stopping the beeping. Please's driving me crazy!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers
Re: Constant beeping

F1 Failed Thermistor Control you will have to Replace Electronic Range Control OR (ERC).. turn off the breaker to stop the beeping..good luck..

Posted on Aug 25, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

5 Answers

I need Please a solution to F1 Error Code on GE/Kenmore electric ovens Model # 911.4658815 Thanks E-mail: I have the same model number. 9114658811 and plugged in the stove for the...


To my understanding error code F1 would indicate a faulty control board, possibly thermistor control. The only recourse is to have this replaced.

This of course would require a fair familiarity of electrical/electronic components/circuitry and safety procedures, use of a DVM and possibly a soldering iron. It would be to your added advantage access to a service manual or at the very least a schematic diagram with voltage readings. Should you be uncomfortable performing a DIY (do-it-yourself), perhaps your best bet would then be to seek the services of a qualified professional.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Oct 13, 2008 | Kenmore 46123 Stainless Steel Electric...

1 Answer

Oven display not working

Hi iron451,

The "F0" error code description is a stock function key. Here are basic test that will help you to determine if the ERC or touchpad is defective.

1. Unplug the range power cord or turn the power off to the range at the circuit breaker.

2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.

4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.

5. Turn the power back on.

6. Wait for at least one hour to see if the code comes back.

7. If F0 comes back, replace the ERC. If it does not, replace the touch pad.

Hope it helps.

Thank you for using FixYa.

Mar 16, 2009 | Dacor Preference RSD30 Gas Kitchen Range

1 Answer

Caloric gas range problem

F0 - F1 - F7 Stuck keypad may mean relay is turned on. Determine if problem is with the Key Panel or Control by:
1. Pushing CLEAR/OFF pad.
2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

If code recurs, problem is in the control. Replace control.

If code does not recur, problem is with the Key Panel.

Dec 24, 2007 | GE Profile Spectra JGBP90 Gas Kitchen...

1 Answer

Oven range not working, oven control beeps and displays -F1-

this model is ether a verson 2,3 or 4 the code for version 2and 3 is: F0 & F1 EOC (Electronic Oven Control) failure Replace verson 4 is;
F1 Circuit board defective Replace control board

Dec 22, 2007 | Frigidaire FEF336BC Electric Kitchen Range

2 Answers

F1 and F2

Here are the codes for Tappan ranges:

Range/Stove/Oven Fault Codes Failure
Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F2 Oven too hot Check Bake function, if OK, replace oven temperature sensor F3 Oven temperature sensor open Check oven temperature sensor, should be ~1100 ohms at room temperature. If too high or low, replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5, 6, 7 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F8 Lock switches Check switches and replace if necessary

Nov 06, 2007 | Tappan TGF363 Gas Kitchen Range

3 Answers


No F7 in my tech sheet Could it be a F1 Failed transistor in control If code cannot be cancelled, replace the Electronic Range Control (ERC) or touch pad if you want to do it yourself let me know...

Aug 25, 2007 | GE Profile Spectra JGBP90 Gas Kitchen...

Not finding what you are looking for?
GE Profile Spectra JGBP90 Gas Kitchen Range Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Barrett Palumbo
Barrett Palumbo

Level 2 Expert

1772 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides