Question about Panasonic PT-44LCX65 Television

1 Answer

The tv wont turn on

When I turn on the power button it blinks green a few time then starts blinking red 2 blinks at a time, and the bulb light starts flashing red 2 blinks at a time.
Panasonic PT-44LCX65

Posted by on

  • 6 more comments 
  • monroe1550 Dec 14, 2008

    the manual says if its the lamp couver it will blink orange twice. But my tv blinks Red twice on the power button and on the bulb button. Thank you for your help

  • monroe1550 Dec 14, 2008

    Can you tell me how to reset the lamp timer? I have no remote for the tv.

    Thank you

    Tony

  • Anonymous Mar 15, 2014

    2 blinks

  • Anonymous Mar 15, 2014

    TV wont turn on red light just flashes

  • Anonymous Mar 19, 2014

    TV turns off after turning it on then lcd Light blinks 2 times first then blinks once every 3 seconds after.

  • Anonymous Mar 27, 2014

    TV Froze. After turning it off, it wouldn't come back on. Now red light blinking.

  • Anonymous Mar 29, 2014

    my TV 32S310 IS PROBLEM IS EIGHT TIME RED BLINKING

  • Anonymous Mar 31, 2014

    turn it on works, connect cable works few minutes then screen goes blank

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 151 Answers

Hello 2 blinks on this tv means you have this issue below
PT-44LCX65
2 blinks 5 secs you have your lamp cover open

check for this

hope this helps

Posted on Dec 14, 2008

  • 1 more comment 
  • charlie rodriguez
    charlie rodriguez Dec 14, 2008


    1. Tighten the screw of the Lamp Cover.

    2. If still NG, replace the Cover SW (SW2911) on the Cover Switch C.B.A.

    3. If still NG, replace the TV unit (Main C.B.A.).

  • charlie rodriguez
    charlie rodriguez Dec 14, 2008




    these are the fualts for the 2 times on the temp light

    these are fualts for 2 times on the lamp light





    temp light Abnormal Temperature

    (Thermistor 1 C.B.A.) flashes twice every 5 seconds



    lamp light Ballast Error (abnormal Lamp voltage) flashes twice every 5 seconds





    sorry i didnt know what light you meant these are for the other light codes fualts

  • charlie rodriguez
    charlie rodriguez Dec 14, 2008


    Be sure to reset the Lamp time to "0" after replacing the new

    Lamp.

    1. Plug in the AC Cord, and turn on the power by pressing the

    POWER button.

    2. Press and hold the VOLUME DOWN button on the unit and

    the SPLIT key on the remote together for over 5 seconds

    in power on condition.

    When the reset is finished, the display as shown in Fig. 5-

    1 appears and the LAMP LED goes out.


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Toshiba remote control se-r0077 sometimes works to control the DVD player and other times it doesn't. I've tried new batteries and the problem still persist s


One of the best ways to check if an infra-red remote controller is working properly is to look at it using a camera. (a webcam or phone camera will work) The camera will see the infra red radiation as visible light. If the LED lights up (on camera) consistently when buttons are pressed, then it may not be the remote at fault, but rather the receiver in the DVD player. Most of the time though, it IS the remote control at fault, and these are usually easy to get working again.

Couple of things to check are:

1) the battery terminals...
Batteries can leak and corrode the terminals in the battery compartments. Signs of this include rust, green coloured contacts, or a crystalline deposit. If you see any of this then clean the contacts using metal cleaner or some methylated spirit and cue-tips.

2) Broken wires connecting battery terminals to the circuit board...
The soldering in some remotes can be rather poor, and wires can sometimes come loose, especially if a remote has been dropped or bashed about a bit. Unscrew the remote and check everything is connected properly


3) Dirt under the buttons...
This can prevent a button from making contact with the circuit board properly. Unscrew the controller and separate the rubber button pads from the circuit board check for dirt both underneath the pads AND on the metal contacts on the circuit board. Clean as required with methylated spirit and cue-tips and then reassemble.


Hope that helps!

Jan 07, 2017 | Toshiba Televison & Video

1 Answer

My sony wega kf-50E200A tv keeps turning off. during each cycle the green light blinks 42 times and the tv comes on again for about 3 minutes and it happens all over again


More than likely the power supply is defective, but without testing and the repair manual that is just a guess, you make the decision to replace or repair the TV.

Jan 07, 2017 | Sony KF-50E200A TV Lamp with Housing

2 Answers

I have sound but no picture on my tv


This is a popular question. Most of the time you either need to make sure all connections are not loose or just need to turn off your tv and receiver and unplug. Wait for 1 minute then reboot.
I recommend this short video as it walks you through some diagnostics for other possible problems.
Repair TV With Sound But No Picture

Nov 24, 2015 | Luxor Televison & Video

1 Answer

Sony bravia shuts off


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

Aug 30, 2014 | Televison & Video

1 Answer

How to determine if it is a power failure or a faulty TNPA5335 board?


The Ysus board is possibly faulty. There is a repair kit available for it containing a few components and all semiconductors!

Jul 08, 2014 | Televison & Video

1 Answer

How do i fix my elonex tv


switch off.wait for 5 mins.
press & hold power button till it turns on then off.
ifno luck try this-
switch on by pressing power button while holding volume + and -.
keep hold of both until powers on.
can take few mins.
good luck!!!

May 04, 2014 | Televison & Video

1 Answer

No Video Or Sound - Stand By Light Flashes 5 Times


If the tv was made before December 2008, there is a capacitor settlement from a class action lawsuit by Samsung. Supposedly (at no charge) they will send a repairman to replace the capacitors.

Nov 27, 2013 | Televison & Video

1 Answer

Would like to know the codes for a LG tv, Sony tv, and a TOSHIBA DVD ?


How to Program


Remotes With SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press "SET" Hold until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


Remotes Without SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press and hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed, at the end of the 4th digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


MAGIC SEARCH FUNCTION
1. The magic search function enables you to scroll through the entire code list one by one by pushing the on/off button. Each time you push the on/off button the remote automatically switches to the next code in the list and sends a signal to the device you have chosen.
2. Choose and press a device key i.e TV. LED will flash once.
3. Press and hold the SET button or if no SET button then hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
4. Enter the 4-digit Device code (refer MAGIC list) i.e TV is 0001.
5. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process.
6. Start scrolling by pushing the ON/OFF button as soon as your TV or Chosen device turns OFF lock the code in by pushing the DEVICE key again.

Mar 27, 2013 | Televison & Video

3 Answers

Need instructions to add TV button to AKB36157102


1. While pressing and holding down the TV POWER button, press the CHANNEL UP or CHANNEL DOWN repeatedly until your TV is turned on (or turned off if you had it on). 2. Release TV POWER button when the TV turns on or off. The remote's TV POWER button will now control the TV.

Jul 19, 2009 | Televison & Video

1 Answer

URC-22B doesn't work with my BEKO tv.


Check with this method. Manually turn on your tv.
Then push and hold the code saerch button until the light stays lighted release the button.
Push and release the device button you want to set TV.
Now you got to push and release the ON/OFF button until your device turn off when your device turn off stop and push and release the enter button for storage the code.
Warning: You may push and release the ON/ OFF button for almost 200 times.
Good luck.














.

Jun 12, 2009 | Televison & Video

Not finding what you are looking for?
Panasonic PT-44LCX65 Television Logo

Related Topics:

1,462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

4758 Answers

The Knight
The Knight

Level 3 Expert

71672 Answers

Jaime Hernandez

Level 3 Expert

2294 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...