Question about Washing Machines

Open Question

Kenmore Elite Oasis Quiet Pack 2 total care flex washer with a error code "F" it beeps and flashes

Posted by on

  • 1 more comment 
  • sparkyis918 Dec 14, 2008

    model # 110.27042600

  • amathews33 Jan 19, 2009

    just a couple of minuets into the wash cycle the washer shuts off, beeps and the letters F/H begin to flash.

    model number 110. 4587

    amathews33@yahoo.com

  • Josh Murphy May 11, 2010

    Unplug then replug in. need the actual model number from the washer.

×

5 Suggested Answers

kapishtech
  • 2272 Answers

SOURCE: Kenmore Oasis Elite Top Loading Washer with an F2 error

The F02 error code indicates keypad/user interface failure. Most of the time, this is caused by a problem in the keypad/user interface. It can sometimes be caused by a failed control board.You could have an intermittent problem such as a stuck key or contact. As long as the F02 is not displayed, the washer should work normally. You can continue to use it when the F02 is not displayed. It is still safe to use the washer.
Sometimes this problem is caused by a loose wiring harness connection between the keypad/user interface control board and the machine control board.
The F2 error code on this washer indicates a stuck button on the user interface control board. The procedure for accessing the control boards on this washer is shown in the image below. I recommend unplugging the washerand checking the wire harness connection from the user interface control board to the machine control board. Try unplugging the connections and then plugging them back in a few times. Make sure that they are plugged in correctly and then reassemble and test the washer. If the F2 is still displayed, then the user interface control board will need to be replaced.
CLICK ON THIS LINK TO GET THE INSTRUCTIONS HOW TO REMOVE CONTROL BOARD:--
http://media.fotki.com/1_p,wfbgkftgqtgssggxgtqsskgwtqkq,vi/gdqwksfbdxggskbksbb/1/1303472/5961857/image8028img-or.gif
You can order a new user interface control board from the Sears PartsDirect website or from----------
www.repairclinic.com
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.



Posted on Jul 26, 2010

blueextc3221
  • 15935 Answers

SOURCE: I have a Kenmore Elite Oasis quiet pack 9 and I am

The F1 error code on this washer indicates a Primary Control Board failure.



It is likely that the machine control board will need to be replaced to correct this problem.



The part number for the machine control board is undetermineable because you have not provided me with the exact model # of your washer.



The procedure for replacing the machine control board is provided HERE

LINK: http://media.fotki.com/1_p,wfgstgtftbtkrrdxgtqsskgwtqkq,vi/gfsfgfsgqxgfqtqtgwf/1/1303472/5961857/image55806img-or.gif



NOTE: Be sure to unplug the washer to disconnect electrical power before accessing internal components.



There is a slight possibility that a problem with the pressure switch hose could be causing this problem.

A pinched or twisted air hose can cause this fault code.

When you open the console, check the air hose connected to the pressure switch on the machine control board.

If it is pinched or crimped, I recommend rerouting the hose to resolve this problem.

This may fix your problem without replacing the control board.



NOTE: You may want to check for this condition before ordering the control board. Most electronic control boards cannot be returned for a refund or credit.



If you find no apparent problems with the air hose on the pressure switch, then replacing the machine control board on this washer should correct your problem. There is a risk involved in replacing this part yourself.

As noted above, you could have a problem with the air pressure hose that is not apparent upon your initial inspection. A service technician would normally need to properly and thoroughly diagnose this problem before replacing the control board.





Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Posted on Sep 18, 2010

blueextc3221
  • 15935 Answers

SOURCE: my kenmore elite oasis He washer model 110.2708260...

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 27, 2010

Daniel S
  • 4323 Answers

SOURCE: I have a kenmore Elite Oasis Top Loading Washing

Hi

This issue can either be due to the suspension rings or due to motor issue. Please check this link for exploded diagram of your washer---

Kenmore Elite Top Load Washer 110.28032701 Diagram

Also, check the stator motor and the retainer, make sure no parts are missing. Hope this helps... Please post back if you need more information.

Daniel

Posted on Dec 30, 2010

oldTech2332
  • 2341 Answers

SOURCE: can wash my clothes washer is giving a f1

Hello,

The F1 error code means that the control board has a detected a problem within the control itself and the control board would need to be replaced.

The part number for that control board is W10189966 it could be picked up at your local appliance parts store or online at;
searspartsdirect.com
apwagner.com
partselect.com
apdepot.com
repairclinic.com


GENE

Posted on Oct 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I unclog the long drain Kenmore elite oasis?


Honestly, we got rid of the machine and bought a Maytag Neptune. I was over trying to figure out all the codes the Oasis was flashing. We gave up on the first one that started having problems when a friend gave us one identical to ours and it has done a lot of the same things.

Apr 03, 2014 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

I have a kenmore elite total care flex king size capacity plus quiet pak2 oasis that makes loud noises like a airplane when its in the spin cycle Model #110.28032701 which parts should be change?


If the washer is roaring during spin, the bearings are bad and you will need to replace the outer tub assembly.
Here is the part to order.

The part comes with a 365 day, any part, any reason return.

Nov 03, 2012 | Kenmore Washing Machines

1 Answer

Kenmore oasis HE Top load Washer stopped in the middle of a cycle. No power and will not unlock


error code? totally unresponsive? try reseting power then if unresp. replace main control. verify 120v into board. 3 screws on rear of console and lift.

Sep 16, 2012 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Can wash my clothes washer is giving a f1 announcement and stops.is a kenmore elite oasis model 110.27032602 quiet pak 2.thanks


Hello,

The F1 error code means that the control board has a detected a problem within the control itself and the control board would need to be replaced.

The part number for that control board is W10189966 it could be picked up at your local appliance parts store or online at;
searspartsdirect.com
apwagner.com
partselect.com
apdepot.com
repairclinic.com


GENE

Oct 12, 2011 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

In mid wash the Kenmore Elite Oasis HE flashes F51 and


check if basket turns freely. if it does replace the main board

Jan 28, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

I hadn't washed any laundry for a couple days and then my Kenmore Elite Oasis starting beeping in the middle of the night. My husband had to unplug it because it wouldn't stop. The next morning I did some...


According to the Whirlpool Cabrio (Sears Oasis) manual, this code indicates a "stuck key"

Keypad/User Interface Failure
F then 2 flashes when in:
• Diagnostics Test mode if a stuck key is detected.
• Standby mode if there is a user interface mismatch.

Following is the PDF of the manual.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/409753510a90c8be852571e90073421b/$FILE/8178583.pdf

Sep 22, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Elite Oasis HE. I keep getting a F2 error and a beeping sound. Will happen at anytime, not just when using the machine. Washer had been unused for 2 days and all of a sudden the error code just...


“F02” is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a “SUDS” error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:

1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.

To check the drain pump, click on the following link for step-by-step instructions.


http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 21, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

I have a kenmore oasis elite it beeps all the time and flashes F2


Code F2 means a stuck button. I removed the interface and lightly sprayed each with contact cleaner. So far this is working. The interface costs about $160 and contact cleaner, $10. Good luck.

Mar 18, 2009 | Washing Machines

1 Answer

Kenmore Oasis Elite---110-27086601


This error only shows in diagnostic mode, with power off choose any buttons except stop and power, press in intervals 5 seconds on and 5 seconds off until 88 appears and all light light up. If the user panel is faulted F 2 will flash in the display, press the same button you used to start diagnostics to jump to the next error code and once through 88 will flash and diagnostics will start. Sometimes once F2 flashes and the machine has not been repaired it will stick at that mode.

Aug 07, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63577 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...