Question about Hoover AI130 Front Load Washer

1 Answer

Clothes stuck in washing machine

Can someone tell me what error message 3 is. I have clothes stuck in the machine and cannot find my washing machine manual. Thanks for your help!! Eileen

Posted by on

1 Answer

Re: Clothes stuck in washing machine - Hoover AI130 Front Load Washer Washing Machines

Thanks repair man called and problem fixed

Posted on Mar 28, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My whirlpool washing machine is reading e2f3. My clothes are locked inside. I need to get my clothes out. I cant get a technician out until tomorrow. How do I get my clothes out?

Just unplug the machine and wait for the lock to release.
The error is a temperature sensor error message and could be due to a broken wire, fairly common with some whirlpool machines.

Mar 11, 2016 | Whirlpool Washing Machines

1 Answer

Frigidaire Atf6700fs2. Machine is giving me message E90. Can someone tell me plz what this means? Ty

The E90 error code is not a common error but it may occur when the washing machine electronics get wet for some reason. This may happen if wet clothes are left in the washer for a prolonged period after the wash cycle ends or if the same load is washed repeatedly.

Read more:

Nov 09, 2013 | Washing Machines

1 Answer

5d error code kenmore he2plus

Here's a video prem mathew suggested as a solution to your problem from YouTube:

Kenmore He2 washing machine washer drain problem fixed

Apr 26, 2013 | Kenmore Washing Machines

1 Answer

Error code "UE" clothes have

UE = Unbalance Error

Laundry load is unbalanced, manually loosen any tangled laundry.
If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.

Thanks for using FixYa !!

Dec 12, 2010 | Washing Machines

1 Answer

Samsung P801.washer....Error Message " ED" WHY??

"ED" is a door open error. try Closing the door properly or else there might be jam at the door.

Dec 12, 2008 | Samsung WF337AA Front Load Washer

7 Answers

Maytag neptune mah8700aww wont drain, spin or put water in

if you remove the oval cover in the back of the mach,you will find the pump.there are 2 hose clamps to remove.usually you will find change stuck in the pump.remove the screws on the bracket that holds down the pump and you can take the entire pump out...good luck

Sep 28, 2008 | Maytag MAH8700A Front Load Washer

3 Answers

"OL" error message

I believe that I had this same problem. The machine was skipping the wash cycle. After the water level rose to where you would expect the machine to go into an agitation cycle to wash clothes; it would start a spin cycle and drain the water. In the process of spinning it would stop to display the OL message over and over again as quick as you redistribute the load.

I found the problem to be clothes that got stuck underneath the impeller (round thing at the bottom center of the basket). Somehow I also had clothes get pulled down and got stuck underneath the basket next to the lint filter, these items were shredded to the point that they probably were not causing any issues, none the less they should not have been in there. Even though it was not the problem, I went ahead and took out and cleaned the lint filter since it was within reach.

This machine works a bit different then other machines. The agitation cycle is dependent upon the basket floating up and disengaging from the drive shaft. I guess the clothes that got stuck beneath the impeller did not allow the basket to float high enough to disengage from the drive shaft. Because the basket was still engaged to the drive shaft the drive motor would spin the basket and start a drain cycle rather agitate the load to wash it. The imbalance of the basket caused by the clothes stuck underneath the impeller kicked of the OL error since the basket was spinning at an unacceptable angle. I am not a repair dude but based on my observation of what I did to fix the problem this explanation works for me.

I've attached some pages of a repair manual that I found on-line to illustrate the areas that I am referring to.

Mar 16, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Maytag epic front loader

Suggestion: Check the wall inlet to see if water comes freely; then check if the inlet valves behind your machine to see they are not clogged. Best that u open the valve full before you begin your wash. The water coming 3 inches/door is normal. Dont try opening the door until after you hear a click or aft 2 or three minutes aft wash cycle completes.

Sep 11, 2007 | Washing Machines

Not finding what you are looking for?
Hoover AI130 Front Load Washer Logo

362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides