Question about Aiwa AV-D57 Receiver

1 Answer

Clock This is a minor problem, yes, but I don't have a remote or owner's manual any longer and I can't figure out how to change the time! Any suggestions out there?

Posted by on

1 Answer

Re: Clock

Turn the receiver on, then press the little button in the remote that says "Shift" with blue letters , then press button with number 2 in it. If you notice it also says "clock" in blue letters. Hold Shift and clock with the receiver on then use the multijog dial, the big round thing in the middle, and set the time.

Posted on Mar 30, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Aiwa XR-EM50

This was easy.. download the manual here:
From the manual:

Clock Adjustment: (Page 7)

Setting the clock
1 Hold down SHIFT and press CLOCK on the remote
When the unit is turned off, you can also press SET.
2 Within 6 seconds, press "< <" (rewind icon) or > > (fast forward icon) to set thetime.
Each press changes the time in 1-minute steps.
Holding these buttons down will vary the time in 10-minute
3 Press SET.
The time display stops flashing and the clock starts from
00 seconds.

When setting the clock on the unit in stop mode, hold down
"square" (stop icon) and press "> >" in step 1. After setting the time in step 2,
press TONE in step 3.

To display the time while the power is on
Hold down SHIFT and press CLOCK on the remote control.
The time will be displayed for 6 seconds.

To switch to the 24-hour standard
Display the time and press s within 6 seconds.
With each press, the clock alternates between 12- and 24-
hour standard time.

In the 12-hour standard, "AM12:00" indicates midnight and
"PM12:00" noon.
If the clock display flashes when the unit is turned
There has been a power interruption. Reset the clock.

Bass / Treb Adjustment: (Page 11)

1) Press BAS or TRE
2) Within 6 seconds, turn VOLUME (press VOLUME +,- on the remote control).
Each level can be adjusted from "-2" to "+5".

Good Luck!

Apr 07, 2014 | Audio & Video Receivers

1 Answer

We dont have the manual for our TEAK AGV 1200 RECEIVER AND I NEED TO KNOW HOW MANY WATTS IT HAS? Any way I can find out with the manual?

You have to type alpha-numeric gibberish verbatim or there will be no good information coming back.

If you mean TEAC AG-V1200 then just google it.

Here's a manual for $10

It probably has the specs.

This seller claims 110 watts per channel all around, which sounds supsiciously generous. Rear channels don't need that kind of horsepower.

Aug 04, 2011 | Teac AG-780 2 Channels Receiver

1 Answer

My Whafedale WH-AV4337 remote switches the unit on and off but will no longer feed the TV sound to my speakers. The AV (Digi) flashes "unlock". I don't have a user's manual. Any...

Hmm, I don't know why the emphasis is in the remote here.

Front panel switches still exist on most products so ramble across the room and try touching it with your finger so we don't have to factor in a possible remote malfunction.

I can't locate a free manual anywhere but YOU should contact Wharfedale and ask them where you could get one because the website only lists a handful of speaker downloads.

However the digital audio for the "AV" is arriving, it is probably not syncing up or the signal / cable is failing or disconnected. Try swapping with known good cables or input jacks.

Jun 19, 2011 | Audio & Video Receivers

1 Answer

Describe your kenwood manual "ka

Hi, Yes it is safe to leave this connection unhooked. The system control is what the stereo uses to remote control a cassette deck,cd,turntable etc... using the amplifier separately should be o.k. I hope this helps, good luck and thanks for choosing FixYa-Prodzilla

Apr 20, 2011 | Audio & Video Receivers

2 Answers

I would like to operate a Samsung HD Cable receiver (DCB-H360R) by means of a Yamaha remote control (RAV293). I have tried all Samsung remote control codes as specifid in the Yamaha Owner Manual, but no...

Yamaha remote supports only those codes that are in the manual (they are pre-programmed in the remote), so no other code can be used. Your only option is to try codes from different brand in the manual (if not done already) or buy a universal remote, which you can program both for Samsung and Yamaha.

Nov 28, 2009 | Yamaha Rx-v465/rxv465 Home Theater...

1 Answer

I have a Zenith Clock Radio Model#Z213B Serial#ZRS04952730 that i bought at a Thrift store. My question is,did this radio originally came with a remote? I`ve noticed there`s a small window on the front of...

Yes - I have it too - - - - and it has a remote (though one of the buttons on it doesn't work) When I get home I'll find out more.

Question for you - - - - I had power outage recently and lost the radio presets. (And I can't find the manual). Do you know how to set the radio pre-set buttons??

Apr 08, 2008 | Audio & Video Receivers

2 Answers


Go to aiwa's website, and search for the AVDV75...or use the link below:

Jan 29, 2008 | Aiwa AV-DV75

3 Answers

Denon avr-1700

If you have the owner manual check for reset and reset the unit. If you don?t have the manual unplug the power cable for a wile and then try again. Good Luck Toufic Malek

Sep 23, 2007 | Denon AVR-1700 Receiver

Not finding what you are looking for?
Aiwa AV-D57 Receiver Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aiwa Audio & Video Receivers Experts

The Knight
The Knight

Level 3 Expert

66685 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers


Level 1 Expert

41 Answers

Are you an Aiwa Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides