Question about Home

1 Answer

MY JACUZZI HOT TUB STOPPED HEATING

IT'S AN OLDER MODEL WITH NO DIGITAL DISPLAY ON THE CONTROL PANEL. IT HAS A RHEOSTAT TYPE DIAL CONTROL WHICH LIGHTS UP WHEN THE HEATING ELEMENT IS ON AND A SINGLE BUTTON (MEMBRANE TYPE LIKE A MICROWAVE) WHICH CYCLES THROUGH PUMP,JETS W/LIGHT, JETS W/O LIGHT AND OFF. I USED IT ABOUT A WEEK AGO AND TODAY I WENT TO CHECK THE CHEMICALS AND THE WATER IS COLD. IT'S 15 DEGREES TODAY SO I DON'T HAVE MUCH TIME BEFORE STUFF STARTS FREEZING (IF IT HASN'T ALREADY) THERE IS NO ICE IN THE TUB YET.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 125 Answers

Sounds like it could be either the heating element, the thermostat or pressure switch problem. Does the light come on when it is trying to heat? if it doesn't come on then most likely the heating element needs to be changed.

Posted on Feb 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a jacuzzi whirlpool modelz145, h240000 it keeps running on low never shuts off this just happened never did this before? Bad control board?


Is this an outdoor hot tub?

If it is an outdoor hot tub...is it heating up or just running all the time?

Sep 21, 2014 | Jacuzzi Home

1 Answer

Why is hot tub over-heating past max temperature?


Sounds like a problem with the thermostat.

Aug 05, 2014 | Jacuzzi Home

1 Answer

Circuit braker keep popping


Sounds like the heating element has gone out again. Once you reset the circuit breaker and the tub turns on it will start to circulate the water. This usually runs like this for about 2 mins and then the tub will recognize it is cold and send power to the heater. If the element is back at that point it will blow the circuit breaker.
If this circuit breaker pops as soon as you turn it on then you most likely have a bad circuit board.

Rod
www.uspartscenter.com

Jan 30, 2013 | Jacuzzi Home

1 Answer

Jacuzzi hot tub, Water is too hot. Heats until it trips the system. I have replaced the analog temperature control,


1) Safety question first
Why hasn't the GFCI tripped.
If your spa is not protected by ground fault., then you are at serious personal risk.
http://waterheatertimer.org/How-to-wire-GFCI.html#arc-fault

2) Replace the element.
http://waterheatertimer.org/How-to-test-water-heater-element.html

3) If element is cracked, it can continue heating to ground wire, causing runaway heating.
This applies to spas, and water heaters of all type.

Dec 08, 2012 | Jacuzzi Pool & Spa

1 Answer

My hot tub top control is flashing SPA6,and hot tub is not heating up.


Here is a link for you to resource that error code.
click that link and scroll through them until you find your error code.

Rod
US Parts Center

Aug 19, 2012 | Jacuzzi Pool & Spa

2 Answers

Can't unlock jacuzzi hot tub control panel


control panel not working, cannot control or work control buttons, stays in econ mode all the time. Nothing else works.

Nov 27, 2010 | Jacuzzi Pool & Spa

1 Answer

I have a Jacuzzi Z110 hot tub. the top control is broke (pn 51422). Can i use a digital top control PN 33334.


When dealing with a big manufacturer like Jaccuzzi, it is unwise to swap top side controls. They make theirs proprietary on purpose so that swapping is more difficult (especially jacuzzi).
If you use the wrong one, the buttons on the controls will be misleading (such as temp up button cycling jets, or the ozone button cycling the lights, etc)
I would use manufacturer part.

Oct 01, 2010 | Qca Spas Jewel Series Topaz Plus Hot Tub

1 Answer

Jacuzzi tub not heating


O ring set may be required slow job take care

Sep 18, 2009 | Home

1 Answer

Need a users manual


Kathy,

I think what you're looking at are the part numbers for the heater and control systems used in some Jacuzzi hot tubs rather than the Jacuzzi model number. I ran into the same issue and discovered through some cross-referencing on the web (jacuzzi parts suppliers) that this is the part number control unit made by Balboa. Odds are they were used in multiple Jacuzzi models.

My suggestion: Look here http://clearcreekspas.com/model_id.html to identify the control panel for your Jacuzzi and then follow the link to the correct manual. Some cover multiple models so you will need to know the electrical requirements of yours (120 V or 240 V?) and then check the layout of each tub shell to determine which model is yours.

I figured out mine is a Jacuzzi Essence Model 350 this way.

Good luck!

Nov 11, 2008 | Balboa Instruments Garden

2 Answers

No power to the display panel


Watch the panel as somone turns the power off and on and see if anything shows up like dashes. The only way to check a panel/ keypad is with a good one

Oct 19, 2008 | Balboa Instruments Duplex Digital Panel 2...

Not finding what you are looking for?
Home Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Experts

Donni Steen

Level 3 Expert

659 Answers

john h

Level 3 Expert

7409 Answers

Brad Brown

Level 3 Expert

14742 Answers

Are you a Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...