Question about Kenwood KDC-138 FM / AM Receiver

1 Answer

I have a KDC-138/cr. I installed it fine and was adjusting the balance, turned the system back off and on and now I have no output to my speakers.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Do you have an owners manual -- ? I have a copy of you need one.. just send me your email address and I will forward it to you

Posted on Mar 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is no sound comming out of speakers


Try checking your speakers and speaker wires for any shorts or grounds. If they all check out good, you may have a bad output ic.

Jun 13, 2011 | Kenwood KDC-138 FM / AM Receiver

1 Answer

I just purchased a new kenwood KDC-138 head unit as well as two car speakers. The speakers were able to be installed onto my 2000 mercury cougar but the head unit gave me some troubles. The wires on my new...


The following will help you out. The first is for the vehicle and the second for the stereo. Good Luck.
Constant 12V+ Orange/Black Switched 12V+ Yellow/Green Ground Black/Green Illumination n/a Dimmer White/Green Front Speakers 6" Doors Left Front (+) White/Black Left Front (-) Gray/Black Right Front (+) White/Red Right Front (-) Gray/Red Rear Speakers 6" x 8" Side Panels Left Rear (+) White/Purple Left Rear (-) Gray/White Right Rear (+) White Right Rear (-) Gray
iadame_17.jpg

May 16, 2011 | Kenwood KDC-138 FM / AM Receiver

1 Answer

How do I adjust my subwoofer bass level for my kenwood kdc-138 car tereo


http://www.kenwoodusa.com/Support/Car_Entertainment_Owners_Manuals/ You can download the manual from Kenwoods site. While the unit is in Standby mode, press the B.Boost button for a second or two. You should now be in the Menu. Select SWPRE. Now chose SW from the (R*/SW) options. The output of your CD player is now a dedicated sub woofer output. I hope this is what you meant. There are many settings regarding the sub woofer and generally the sound in whole. Getting the manual is highly advisable. dreamsystems.

Feb 08, 2011 | Kenwood Car Audio & Video

1 Answer

No sound on kdc - 138 and i know everything is hooked up right got power in everything i got a little sound but not for long


Im in the same boat... im searching for a reset... mine worked for 30 mins.. once i moved it from my van to 4runner... then I got back in teh car everything turned on but no sound.. i thought a speaker had shorted but nope.. im wondering if there is a reset

Jan 20, 2011 | Kenwood KDC-138 FM / AM Receiver

1 Answer

Kenwood kdc-138, NO SOUND, CD PLAYER NO RESPONDING


First thing you need to do is make sure you dont have a short in the speaker wires.. if any one of them touches ground it kills the system.. then you have to remove all the wires and start over... disconnect the battery... remove all the speaker wires only and then turn it on and reset it... then again remove the battery from the car and install them all make sure nothing is touching then turn it back on and see if that works.. you can also test to make sure you speaker wires are good by using a 9v battery and touching positive and negative of each speaker to the positive and neg of the battery... JUST FOR A SECOND it will pop.. that means your wires are good and no shorted to that speaker.

May 12, 2010 | Kenwood KDC-138 FM / AM Receiver

1 Answer

Install


I hav a problen with ic amplifier of audio KKZ12 I need to remplaice or need more information with this

Nov 23, 2009 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

How do i get my kdc-138/cr out of the demo mode?


press the center of the control knob for 2 sec

each time you press it will turn off or on the demo mode.

Mar 27, 2009 | Kenwood KDC-138 FM / AM Receiver

2 Answers

Can't set the time on my kdc-138/CR.


Where can I get part no. Nobel ACV- 310. 100Kx4 for model QR-747A. Pioneer brand music system

Feb 11, 2009 | Kenwood Audio Players & Recorders

1 Answer

Kenwood KDC-138 Operation Problem


Here's the quote from the manual regarding "dcer": "The speaker wire has a short-circuit or touches the chassis of the vehicle and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. If the "PROTECT/DCER" code does not disappear, consult your nearest service center "

I believe the manual can be downloaded from crutchfield .com after you go to the Kenwood KDC-138 page on their website. The reset button is either on the lower left of the face or, removing the face, on the lower left of the body. Hope this helps you.

Jul 24, 2008 | Kenwood KDC-138 FM / AM Receiver

Not finding what you are looking for?
Kenwood KDC-138 FM / AM Receiver Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4766 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

yadayada
yadayada

Level 3 Expert

67912 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...