Question about Pioneer Televison & Video

1 Answer

Pioneer pdp-436pe runs 10 - 15 mins then goes to standby. then standby light flashes twice. Any help please. Peta

Posted by on

  • 1 more comment 
  • Peta Ashby
    Peta Ashby Dec 13, 2008

    Thank you downloaded manual. Yes we have two TV engineers here, find getting advise on Pioneer in UK difficult. Does anyone know the fault code of standby flashing twice. The fan comes on intermittently in media box.

  • Peta Ashby
    Peta Ashby Dec 14, 2008

    Appreciate your help, show the engineer on Monday the manual. Looking along those lines but without manual, like looking for a needle in a haystack.

  • Peta Ashby
    Peta Ashby Dec 15, 2008

    hi do you know where we could get power supply board from. None in stock Pioneer uk. Board number AXY 1129-A. Or power supply upgrade kit.



    thanks for any help

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,594 Answers

Hi,
Please check, does any fan stop running after 10-15 minutes in TV ?
It is Plasma TV and produce much heat as compare to other TVs like LCD or rear projection.
Let me know proceed further.

Posted on Dec 13, 2008

  • 1 more comment 
  • Shahid Electronics
    Shahid Electronics Dec 13, 2008

    You can download service manual from HERE if you know basic electronics and have experience of TV repair and troubleshooting.



  • Shahid Electronics
    Shahid Electronics Dec 13, 2008

    2 times standby blink shows problem in power supply as shown in below picture, taken from provided service manual page-62
    Downloaded service manual has all technical details, schematics (few boards which can be repaired) etc.

  • Shahid Electronics
    Shahid Electronics Dec 15, 2008

    Hi,
    Required power supply board is available in Part Store.
    There are few Refurbished Power Supplies also in Part Store but I'm not sure about that.
    Thank you.


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PDP - 436PG display turns off then straight off and the red standby flashes 3 times, pauses then repeats


That is an error code that likely means power supply issue and based on brand not likely to be a do it yourself fix. Consider having a authorized Pioneer service center look at it and get an estimate.

Nov 05, 2012 | Pioneer PDP-4360HD 43 in. Plasma...

1 Answer

I have a Pioneer PDP-LX6090 standby lamp flashes twice


Plasma TVs commonly have some typical faults, irrespective of Brand. Visit the site named 'Electro-help'. Check this link, and select the site named above. You will get details from there. Pull up older posts.

Jul 17, 2012 | Pioneer Televison & Video

1 Answer

My pioneer plasma tv in standby mode and wont turn on


Try restting it by unplugging the tv for a few mins and it should rest to original factory default settings but leave it unplugged 10-15 mins to be sure.

Dec 18, 2011 | Pioneer PDP-4270HD 42 in. Plasma...

1 Answer

We have had problems switching on our Pioneer PDP-507XD plasma tv. The standby light just flashes. We were advised to change the power supply unit. We hav4e done this and it has not solved the problem ...


I've been running across a lot of plasma tvs where the power supplies are not bad, but the X & Y-sustain boards are faulty. My advice is to change those boards out as they are responcible for lighting the plasma gasses in the tv. You can attempt to replace one at a time (cost reasons), but it is recommended to changed both at once.



Hope this helps, please rate. :)

Apr 11, 2011 | Pioneer PDP-507XD 50 in. Plasma Television

1 Answer

My tv goes blank after 10 - 20 min. of viewing


Your tv has a circuit fault, is the power light flashing, if so this is a code for the service engineer.

---


Please dont forget to vote this answer was helpful and accept my answer.

Many thanks

------

Feb 14, 2011 | Pioneer PureVision PDP-5050HD 50 in....

1 Answer

I have a pioneer pdp 5040 plasma and it just died on me. It will turn on then turn off after 3-4 sec. The standby light flashes 3x pauses then flashes 3x again, can I fix this


PDP-5040 turns on then off after 3-4 seconds / display in upper right corner says user full and record timer led is lit on box / rrepairable?

Sep 27, 2010 | Pioneer PureVision PDP-5040HD 50 in....

2 Answers

Pioneer pdp 503


Hi, my PDP 50XE just cut out, when powered back on the screen powers down and the standby light flashes twice followed by a 5 sec gap.  Anyone got any thoughts? Thanks

Jun 28, 2008 | Pioneer PureVision PDP-5030HD 50 in....

1 Answer

Plasma turened off and red light flases twice


Red flashing x2 = Panel power supply fault

It would be easier to replace the power board than attempt a repair at component level (dangerous voltages)

Oct 13, 2007 | Pioneer PureVision PDP-504HDE 43 in....

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73073 Answers

Jaime Hernandez

Level 3 Expert

2307 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...