Question about Projection Televisions

2 Answers

Yamaha Htr-5560 Av Receiver ,will not turn on makes click-click noise only

Posted by on

  • hoobobhoo Dec 12, 2008

    I tried that and hope the service center did as well?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Had the same problem with a friend's 5560. it was a resistor on the rear center channel board, which is mounted right behind the middle of the heat sink. unhook the two ribbon type cables running to it from the board.

everything will work, except the rear center channel speaker. my friend never used the rear center channel anyway. in the meantime, he bought a new receiver, so i have an extra one for my workout room. woohoo. hope this helps.

Posted on Feb 12, 2009

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

Check the fuses in the back!

Posted on Dec 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a JVC AV-65WP74, I went to bed watching the TV then turned it off for the night but the next day when I turned it back on the blue light came on on the TV but no picture, the TV makes a fast...


The clicking you hear is probably caused by a relay that controls the incoming AC to the main power supply. This is a protective reaction to a problem in the power supply itself or an overload due to a failure downstream from the supply. This is not a likely DIY repair. You will probably need a technician to determine which of these two likely problems it is.

May 19, 2011 | JVC AV-65WP74 Rear Projection Television

1 Answer

Clicking on the power supply board(no picture or sound)


If you hear a buzzing, humming or rapid clicking noises this could be a problem with your ballast.Might be a good idea though to pull out your lamp just ensure its not damaged.You can find these at discount-merchant.com

Apr 01, 2010 | JVC AV-48P575 48" Rear Projection...

1 Answer

BOUGHT JVC AV-56WP74 IN JUNE 2004. 52


It is worth getting an estimate. From the symptom you explained, it looks like the horizontal output transistor became defective.

Jan 16, 2010 | JVC AV-56WP74 56" Rear Projection...

1 Answer

ICs + resistors swapped= blue power light auto on clicking noise


Unplug the power to the convergence board. If it turns on, you still have a problem in the convergence circuit.

Dec 16, 2009 | JVC AV-56P575 56" Rear Projection...

1 Answer

My RAV 250 remote for my HTR 5740 has button issues.


if you can open the remote try cleaning the board this will help make the contact

the other way to test remote is a camra on phone
turn on camra and press the buttons and if you see a flashing light then that button ok try the rest

Nov 28, 2009 | Projection Televisions

1 Answer

My phillips magnavox big screen tv model number 55p8288 doesnt have any sound when i turn it on


Check the audio setting to make sure the internal speakers aren't turned off. Check to see if it's set to use external speakers. If it is setup to run sound through an av receiver check all connections, make sure the receiver is on the correct input setting, and speaker wires.

Jul 05, 2009 | Philips Magnavox 55P9271 55" Rear...

1 Answer

Jvc i art pro doe not turn on


The clicking sound is the TV trying to restart itself. It generally attempts this several times before giving up. The blinking code indicates the type of error (error codes are documented in the manual for the TV). The most likely cause is a burned out bulb, but could be something else.
If it is a bulb, it is usually replaceable without a service technician, and at a cost far less than $450.
Good luck.

Jun 18, 2009 | JVC AV-56WP74 56" Rear Projection...

2 Answers

Makes a poping noise out of the speakers when i turn it on? can ya help plz thnks james


If you have no video and its making a popping noise its mostlikely shorted convergence circuits. Contact www.TvRepairKits.com and ask them to make you a kit for chirping sets.

May 16, 2009 | JVC AV-48WP30 48" Rear Projection...

1 Answer

Clicking and powering off


That's just the relay switch in the power supply trying to come on. Because it clicks right off it sounds like you may have a short in the circuit (power supply or high voltage). Get it looked at by a professional.

C-Dog

Feb 03, 2008 | JVC AV-56WP74 56" Rear Projection...

Not finding what you are looking for?

Open Questions:

Projection Televisions Logo

Related Topics:

368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...