Question about Samsung HCN4226W 42" Rear Projection HDTV-Ready Television

1 Answer

Tv fails to power on red light glows around power button on tv

I turned the tv off for about an hour and when i tried to turn it back on the light which is normally green around the power button was now red with no picture or sound or power. i already had the convergence module replaced on the tv a year ago. any Idea on the power supply.

Posted by on

  • york b Jan 04, 2009

    I have the same problem. the red light comes on blinking with no picture or sound.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is somthing like puse in the back in side it cost u near about 200 $ put that it gone work 101percent

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced lamp on mitsubishi wd62527 worked for 10 minutes then shut down. Now red lamp light is on


If the red indicator light on the front of your HDTV is glowing a solid red, you should first unplug the AC cord from the wall power outlet and wait for 60 seconds before reapplying power to the HDTV.

After you turn the TV on, if it doesn't power up, try holding the power button down for at least 8 seconds. That's supposed to force a system reset. If your model has a system reset button, use that instead. Press the reset button for about 20 seconds...release it and press it again for 20 seconds, release it again and the led will blink just for a minute or two. You should now be able to turn the TV on.
If after several attempts, the HDTV has not fully powered on and the LED on the front of the HDTV is still glowing solid red, you may want to reseat the lamp.

If reseating the lamp has not resolved the issue then your next step is to order a replacement lamp.

Apr 05, 2015 | Mitsubishi Projection Televisions

2 Answers

BLINKING STANDBY LIGHT AND NO POWER


there is a possibility that the power switch capacitor has bubbled or leaked a remedy is to unplug the unit from the outlet for at least an hour then try to power it back on.

i will try to look for more information about other work-around's or which of the other parts are defective or almost defective, that is causing the problem.

Jul 30, 2008 | Sony KP-46WT520 46" Rear Projection...

1 Answer

TV WILL NOT TURN ON AND RED STATIS LIGHT IS ON NO CODES ARE SHOWN. WHAT DO I DO?


If the red indicator light on the front of your HDTV is glowing a solid red, you should first unplug the AC cord from the wall power outlet and wait for 60 seconds before reapplying power to the HDTV.

After you turn the TV on, if it doesn't power up, try holding the power button down for at least 8 seconds. That's supposed to force a system reset. If your model has a system reset button, use that instead. Press the reset button for about 20 seconds...release it and press it again for 20 seconds, release it again and the led will blink just for a minute or two. You should now be able to turn the TV on.
If after several attempts, the HDTV has not fully powered on and the LED on the front of the HDTV is still glowing solid red, you may want to reseat the lamp.

If reseating the lamp has not resolved the issue then your next step is to order a replacement lamp. Keep in mind that some off-brand lamps may only last a few weeks, so replacing a relatively new off-brand lamp may unfortunately be necessary.

Apr 04, 2015 | Mitsubishi Projection Televisions

1 Answer

Screen issues


I think better to replace the set as all this sounds like a light engine failing.

Dec 08, 2012 | Projection Televisions

1 Answer

Sd-p55a3-k/kc this tv does not turn on


Th convergance amps have failed you will half to replace them, or have it done parts are around 70 dollars not and easy fix on a pioneer time consuming

Dec 10, 2009 | Pioneer SD-P55A3-K 55" Rear Projection...

1 Answer

Panasonic PT-53TWD63, TV will not turn on, Red power light blinks


It is most deffinately a convergence chip issue. The die for no reason. They can be bought online for around $10 dollars and anyone with experience with soldering can replace them pretty easily. I have done it.

Feb 03, 2009 | Panasonic PT-53TWD63 53" Rear Projection...

2 Answers

Need Help big screen turns on thens goes off


a tv has two components, firstly a power supply produces high voltage to trigger a line transformer, in turn a transformer produces smaller voltages. firstly check if the ht is constantly been produced from a supply, if this is there than go to a line transformer, and check voltages at the output.

Sep 10, 2008 | Panasonic PT-61HX40 61" Rear Projection...

1 Answer

Wont power on


Needs Convergence amps replaced. Also fuses around this board are out. There should be small pico-fuses open around this board(replace)

Aug 26, 2007 | Hitachi 55FX48B 55" Rear Projection...

1 Answer

Power button Flashes


Bad Convergence circuit , replace 2 STK392-110 & fuse will take care the problem

Jul 18, 2007 | Hitachi 43FDX15B 43" Rear Projection...

Not finding what you are looking for?
Samsung HCN4226W 42" Rear Projection HDTV-Ready Television Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

Donald Griswold
Donald Griswold

Level 1 Expert

8 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...