Question about Frigidaire Heating & Cooling

1 Answer

I need to know how to turn on my gas furnace

I have a13 seer split system.and i know where the gas switch is but what eles do i need to do to get the heat on.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 500 questions.

  • Expert
  • 540 Answers

Turn the gas valve back-on which shouldn,t be messed with ,only turn the unit off at the thermostat only.

Posted on Dec 12, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My rheem furnace is running but isn't lit.

Not sure but its possible your thermo coupler is shot and needs replacing. If you have a pilot light it could be out but the furnace should not start if the pilot is out as there should be no oower getting to the controls unless the pilot is trying to let it start. A bad thermocoupler will not let the flame start.

Jan 17, 2015 | Rheem Complete Split System Gas Furnace 5...

1 Answer

Aircondition builds ice on coil

Either lack of refrigerant, stopped up metering device or capillary tube/s, or lack of air flow (due to bad blower motor, or dirty indoor coil) Good luck.

May 19, 2014 | Rheem Complete Split System Gas Furnace 5...

1 Answer

Furnace shuts off before reaching temperature set on thermostat

SANDRA!? You answered your own question! What is bad then? THE THERMOSTAT! You need a new one; $5-7 at Home Depot

Jan 18, 2014 | Rheem Complete Split System Gas Furnace 5...

1 Answer

Installing Rheem gas furnace, where is the pressure switch and how do i turn it on/off?

Can you be more specific about which switch, what the problem is and what your trying to do? Thank you.

Nov 23, 2013 | Rheem Prestige Series 3.0 ton 16 SEER...

1 Answer


The relay on the outside unit is stuck

May 25, 2013 | Coleman 3.5 Ton 13 SEER Complete Split...

1 Answer

Will not switch on

There should be a box near that. Electric fuse or breaker might be in that, check it. be careful! it is high voltage. Check the other breakers too. If that is not it, let me know

May 02, 2013 | Rheem Complete Split System Straight...

2 Answers

No heat from furnace

If this is the first time unit has been fired up, you likely have air in the lines to purge first. Also make sure the gas supply is on/open. and that if there is a fuse present on the control board (likely a 3 Amp fuse) make sure it has not blown (which can happen simply by close proximity lightning strikes.)

Letting the unit go through the ignition sequence several times will purge the line. If furnace "locks out" on third start attempt, shut it off and start cycling it again until the furnace comes on..

This assumes the installation was checked for leaks initially.

Oct 27, 2012 | Coleman 3.5 Ton 13 SEER Complete Split...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Bill Long

Level 3 Expert

588 Answers

Are you a Frigidaire Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides