Question about Canon PIXMA MP150 All-In-One InkJet Printer

1 Answer

Wastw ink absorber is full

On printer PIXMA MP150 INDICATE E -2- 7
oN COMPUTER WRITE WASTE INK ABSORBER IS FULL

Posted by on

  • 1 more comment 
  • Anonymous Feb 06, 2009

    Waste ink absorber full or platen waste ink absorber full
    how 2 reset


  • hdgal May 11, 2010

    i am getting stuck on #2 for my mp150 -- it shuts off every time i hold it and the stop/reset button together at the same time. it acts like i am not even touching the stop/reset button. is there any other way to get the printer into the service mode so i can clear this E8 waste absorber error?

  • prahladkumar May 11, 2010

    i brot i canon printer mp160 inkjet printer i wanto suppot printer problum E-2,7error so request solution

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Canon Master
  • 4,338 Answers

On step 4, hit the stop/reset button 4 times to clear the waste ink error.

How to clear Error Code Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE


E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Waste ink absorber full


Hi

Do you need to reset the counter in MP150?

Anyways remember that you need to repalce the absorbers also later. Follow the below procedure and you can start using the printer again.

PROCEDURE I. Enter Service Mode:
  • Plug in power cable
  • Hold down STOP/RESET button
  • Hold down POWER button
  • Release STOP/RESET
  • Press STOP/RESET twice in a row
II.Execute Waste Ink Counter Reset Operation:
  • Press STOP/RESET button 4 times (Indicator lamp will blink alternately Orange/Green each time the button is pressed)
  • Turn off the printer by pressing POWER button (wait until the printer is completely OFF)
When you turn on the printer,waste ink absorber full error is cleared and the printer work normally.

Original source: http://www.printerclinic.com/reset-waste-ink-counter-canon-pixma-mp150/#ixzz1SaAjTfWu

Jul 19, 2011 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

My printer shows E 2 7. how can i fix it?


i believe on this model the error code means that the ink tank is full...
http://www.mediafire.com/?s2pa54m5z2wqwru
this is a link to my hosting site where you can download the software reset tool for a the MP models...
To reset waste ink counter at printers canon pixma MP150, MP160, MP170, MP180, MP450 and MP460 there any 2 choice, that is :
  • Start with printer on then run this software
  • Click Reset Main (main) to reset waste ink counter and then click Reset Platen button (additional)
Additional information error codes for the MP models...
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error – USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Aug 07, 2010 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

The waste ink absorber is full


To reset your Canon IP1000 just simply pull out power cord then press-hold power button, while holding power button insert back power cord. You will notice that the power button indicator lights up upon inserting power cord. then you may release power button and start printer. That will solve your "The waste ink absorber is full" message.

Downside is: you may have to do this frequently if your printer looses power. You will understand what i mean.

Jan 04, 2010 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Error 8


Dear sir your problem is or E8 mean
Waste ink absorber full, or platen waste ink absorber full
follow this step0aa6513.jpg

Aug 13, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

I have problem error code e23 for my canon printer pixma mp150 what can i do for solve this problem pls help me tq


Hi raj2006678,

The code e23 indicates a paper feed error. Check to be sure that your paper is loaded correctly and that the rollers are functioning properly.

Here is the complete list of error codes for the MP150:
E2 No paper (ASF)
E3 Paper jam
E4 No ink
E5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed
E16 Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

I hope this helps - please let me know if I can be of any further assistance.

Kind regards,
H2H

Dec 16, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Printer says ''waste Ink absorber is full'' see service center


This is what the manual says: Ink used for cleaning is absorbed in a waste ink absorber placed in the machine. Press [OK] to cancel the error so that you can continue printing. Once the waste ink absorber becomes completely full, printing cannot be done until the waste ink absorber is replaced.
Canon recommends to contact a Canon service representative as soon as possible.

Nov 12, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Waste ink absorber is almost full


Try this:
Resetting overflow error code for Printer Canon Pixma MP110
  1. Turn on the printer.
  2. Click Menu, and then Scan, Copy and Scan again. All - entered the service mode.
  3. Select Counter
  4. Click Copy - everything. Waste dropped to zero.
  5. Turn off the printer POWER button.
Good luck

Oct 14, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

ERROR MESSAGE 2


How do I change the ink cartridge for the Canon Pixma 150

Sep 01, 2008 | Canon PIXMA MP150 All-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA MP150 All-In-One InkJet Printer Logo

741 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96518 Answers

old marine
old marine

Level 3 Expert

1464 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...