Question about Lexmark Printers & Copiers

1 Answer

Need set up Lexmark C534n to our office network.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 236 Answers

Does the printer have an IP already assigned to it?

Print out a network settings page:

Printing a network setup page
If the printer is attached to a network, print a network setup page to verify the network connection. This page also
provides important information that aids network printing configuration.
1 Make sure the printer is on and Ready appears.
2 From the control panel, press .
3 Press until Reports appears, and then press .
4 Press until Network Setup Page appears, and then press .
After the network setup page prints, Ready appears.
Note: If an optional internal print server is installed, Print Network <x> Setup Page appears.
5 Check the first section on the network setup page, and confirm that Status is “Connected.”
If Status is “Not Connected,” the LAN drop may not be active, or the network cable may be malfunctioning.

If that is an IP not on your network, then you need to change that IP to an unassigned IP that is on your network.

You can do that by typing in the IP of the printer into a web browser (example: Http://ipaddress)
Then you should be able to modify the IP address from here.

Once the printer is on your network, make sure you have drivers for it installed and then just map any worksttaion to it.

Posted on Dec 11, 2008

  • Dan
    Dan Dec 11, 2008

    You should be able to set the IP on the printer itself.
    Look for a IP setup on the menu


  • Dan
    Dan Dec 11, 2008

    That menu should be here:

    network menu on the printer , then scroll and select TCP/IP
    and under TCP/Ip select address and enter the new IP


×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Lexmark c534n printer keeps jamming. I have changed the rubber rollers and the photoconductors. However, the paper will not even go up into photoconductor area. The rollers do try to push the papers...


The fuser rollers might be damaged. Check if the fuser rollers are damaged because if they are they can cause the paper jam, and might need to be replaced.

Nov 07, 2012 | Lexmark C534N Printer

1 Answer

Black lines on side of page lexmark c534


Please try to print the menu settings page, if you're getting the black lines, replace the photoconductor for the black toner.
If you need further assistance please contact Lexmark Technical Support.

Oct 14, 2011 | Lexmark C534N Printer

1 Answer

I have a Lexmark C534n color printer error message comes up 120.10 service fuser error. What does this mean.?


It means there's an issue with the fuser, and the fuser likely needs service or replacement. I would not recommend doing this yourself if you haven't done this before, take it to a repair shop.

Feb 24, 2011 | Lexmark C534N Printer

1 Answer

Lexmark c534n printer, warning for depleted color units do not go away after replacement


The supply counter must be reset manually after a photoconductor unit is replaced. Here's an article on How to Reset the Photo Conductor (PC) Page Count After Photo Conductor Unit Replacement on C52x and C53x Series Printers. Just click on this link: http://bit.ly/dk8nHs. Thank you for choosing Lexmark.

Jun 13, 2010 | Lexmark C534N Printer

1 Answer

2 sided print on c534n


goes through below link and download the pdf file in page nuber 50 how to take duplex print....

www.bcplib.org/PDF/Manuals/Lexmark%20c530dn.pdf

Oct 26, 2009 | Lexmark C534N Printer

1 Answer

Lockups and 900.00 Service RIP software errors on C534N printers.


are these printers hooked to surge protectors? 900 rip error is a software communications error and can be caused by any pcb in the printer. any surge, lightning strike,ect can cause the nvram chips to have problems these errors can be intermitten or continuious depending on the damge to the nvram. have you tried isolating any of these to see if it still has the problem off the network?

Jul 15, 2009 | Lexmark C534N Printer

1 Answer

Wrong Media loaded error - tranceparencies


hi!!! in that kind of problem maybe the paper sensor was defective and it can't detect the kind of paper you loaded to your printer.

Apr 18, 2009 | Lexmark C534N Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...