Question about Car Audio & Video

1 Answer

Earthquake PA2050c car amp.

Hello
In this amp. does not work the impulse power supply.
There was several problems Ihave found.It is very difficult to look for problems
on 2 levels PCB. All in all I need the circuit diagram of this product.
Thanks for Your help in advance.

Miklos

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 103 Answers

This company copied the v11 zeus amp @ one time , if its the same type of amp send pictures of the board to catally733@aol.com , i can help u out

Posted on Oct 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring power house phd2 mono amp to the earthquake 4 ohm speakers.


When i hooked up my bass knob the amp made my subs hum i unhook the rca but still humming unhook bass knob still hummin

Jun 12, 2011 | Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

I have a earthquake 700.1 amp with nothing else hooked up to but the power wire and remote and ground i am getting a red protection light anybody have a answer .


Your power supply is toast. Might be repairable at a electronics repair shop. But for an Earthquake amp I wouldnt waste the money.

Dec 22, 2010 | Earthquake Sound PH-700.1 Car Audio...

1 Answer

Problem with Eathquake amp 2000w


the amp dose not have any such internal batery it is probly tosted call me 256-698-9903

Jul 05, 2010 | Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

Fuse for power cable on earthquake PH D2


I would go with a 40 or 60 amp fuse, this should be ok, you will hardly every run the amp to full capacity so its better to be safe than sorry.

Dec 02, 2009 | Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

My amp earthquake ph d2 output mosfet number...rfp 40n10


Hello luistecnico2,

Those cross-reference OK. Go to www.mouser.com and do a search on both numbers. You'll find that one of them was manufactured by STMicroelectronics and is currently obsolete. The other is manufactured by Fairchild Semiconductor and is available at a cheaper price than the original.

Hope this helps.

Jun 20, 2009 | Earthquake Sound PH-D2 Car Audio Amplifier

1 Answer

Red light is on when i connect input cable earthquake 1000w amp


Cables are either shorted, or deck is putting out too much power for input on amp... many new head-units will put out up to 7v on the output jacks (RCA) the amp may only want to see up to 1v will need to consult head-unit manual for adjustment of outputs.

Jan 22, 2009 | Earthquake Sound PH-D2 Car Audio Amplifier

2 Answers

6 channel power 1000watts earthquake amps red is on


This is normally a grounding problem in the amplifer. If you have a volt meter, check the voltage at the ground of the RCA input on the amplifier. If that voltage is anything more than just a few millivolts then you have a problem in the pre-amp of the amplifier. You should also only connect or disconnect the RCA jacks while the system is off. Otherwise you can get a loud popping noise that can damage the amp or the speakers. Check that voltage on the amplifer RCA jacks with the head unit not connected to the amp with the RCA cables, then if that is OK, check the RCA cables coming from the head unit. You may even have a voltage on those RCA's coming from the head unit, in which case, you have a problem in the head unit. You will be looking for a DC voltage, if you have anything more than just a few millivolts (0.070 +/- DC volts) on either of those then you have found the cause. After that, it will require a technician to be able to troubleshoot the amp or the head unit to determain why you have that DC voltage where it should not be.

Let me know if I can be any more help,

Dave

Jan 22, 2009 | Car Audio & Video

2 Answers

Bass sounds flat when volume is increased


probably your power is too short, increase your gauge wire, and your ground wire of the amplifier has to be shortly as possible, and the positive has to be enough to support peak power, you can also put a big capacitor on the positive wire to give some more power while the bass peak.

Apr 26, 2008 | Earthquake Sound PH-D2 Car Audio Amplifier

2 Answers

Earthquake ph-d2


The PWM IC is an SG3525. Which IC are you calling the protection IC?

Nov 02, 2007 | Earthquake Sound PH-D2 Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...