Question about Xerox Phaser 7300DN Laser Printer

1 Answer

Advice phaser 7300dn appear 10: eeprom ,help me please!

Phaser 7300dn appear 10: eeprom call service, please consult the exception of components that counter? how to operate?

Posted by on

  • paghorashy May 11, 2010

    What exactly does that printer say. on the screen

  • Joseph Macarthy
    Joseph Macarthy Jan 08, 2013

    U2 CODE

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 49 Answers

Hi,

The only thing you can do is attempt a reboot and hope for the best, otherwise call out an engineer to repair it! Or you could try and NVRAM reset but I'm not sure if that will work and be careful because you will set the machine to factory settings and may have to do a colour calibration all over again. Let me know how it goes.

Resetting all settings to default (NVRAM)
Resetting the NVRAM will reset all printer values including network, printer setup, job defaults, and color calibrations.

  1. Press the Down arrow key and scroll to Support.
  2. Press the OK key.
  3. Press the Down arrow key and scroll to Service Tools Menu.
  4. Press the OK key.
  5. Reset NVRAM will be displayed.
  6. Press the OK key.
  7. Reset NVRAM and Reset Printer NOW will be displayed.
  8. Press the OK key to reset all the settings to default.

Posted on Mar 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help with u2 code on phaser 7300


U2 is an engine EEPROM failure - you'll need to replace the main board to fix that, I'm afraid.

Jan 08, 2013 | Xerox Phaser 7300DN Laser Printer

1 Answer

I have error on my Xerox Phaser 6180MFP: 116-324 I have unplugged , restarted, checked all connections...help?


116-324: Controller Error (Illegal Exception)

To access Service Mode, press Up and Down Arrows at power ON.
Go to EEPROM Test

EEPROM Test
? Start
? Processing
? Check OK
Performs write/read/verification of the test patterns (0xff, 0xaa, 0x55, and 0x00) on one byte at every 0x400 from the first address of EEPROM.

Sep 14, 2011 | Xerox Printers & Copiers

2 Answers

Fuser upper failure is the message i am getting on my xerox phaser 7300. can anyone help please


Hello, The fuser or fuser roller is what actually bonds or melt the toner on to your paper. There is probably some type of temperature sensor, that senses the temperature of the fuser. If its not hot enough or just plain dead, it will give out an alarm similar to what your getting. You probably need to replace the fuser unit. You have a lower fuser and an upper fuser. You might be able to get away with just replacing the upper roller. The roller has a heating element inside and that's what probably defective.
Hope this Helps
Thank You for your feedback

Jan 31, 2011 | Xerox Phaser 7300DN Laser Printer

1 Answer

My Xerox Phaser 7300DN Laser Printer has lost its IP address. I recently got rid of XP service pack 3, but the day after that my network WAS working well. and I printed quite a volume of stuff. It was only...


unplug and shut down everything for 5 min...... then plug in/reboot in this order....

PC
Router
Printer

Wait until each has started up fully before going to the next item.

Dec 22, 2008 | Xerox Phaser 7300DN Laser Printer

3 Answers

Xerox Phaser 7300DN Laser - Transfer Unit issue


Hold down Back and Information and turn on the printer. You enter in service mode. Then you can reset CRU counters.

Good luck!

Jun 19, 2008 | Xerox Phaser 7300DN Laser Printer

2 Answers

Phaser 7300 Error Code/Message


Seems to be something to do with the Ram.

More help HERE

Jun 01, 2008 | Xerox Phaser 7300DN Laser Printer

2 Answers

Replace Black Imaging Unit


My advice is to throw the printer out the window!! Just a suggestion!

Ted

Jan 30, 2008 | Xerox Phaser 7300DN Laser Printer

1 Answer

Will not print multiple collated two sided publications without individually sending each job


I would try changing the driver you are using. There are multiple drivers and it really sounds like that will resolve your problem.
For the drivers go to Xerox.com.
on the tool bar select Support and Drivers.
Then enter your printer number, being phaser enter phaser 7300 in the search .
Select your operating system and there will be PS and PCL drivers.
I am 99.9 percent sure the issue is in the driver.

Dec 26, 2007 | Xerox Phaser 7300DN Laser Printer

Not finding what you are looking for?
Xerox Phaser 7300DN Laser Printer Logo

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Printers & Copiers Experts

Whit
Whit

Level 1 Expert

185 Answers

iteminconline

Level 2 Expert

110 Answers

Philip Hughes

Level 2 Expert

63 Answers

Are you a Xerox Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...