Question about Delta Enterprise Baby Gear

Open Question

Where can I get parts for my delta model 4885 crib?

I misplaced bolts, have a broken dropside rail, lost the dowels and need to replace the adjustable height supports L&R? Where can i get this stuff, up until know the manufacturer will not help me?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to an Expert (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: Need replacement rails for Delta Luv crib

Call the Delta Products customer service:

http://www.deltachildrensproducts.com/customer_service.asp

They can tell you where to get the parts, or you can ask them for it:

Call Customer Service :
Monday-Friday 9am-5pm EST.
(212) 645-9033


Email:
CustomerService@deltanyc.com

Posted on Mar 24, 2008

Ad
  • 1 Answer

SOURCE: Delta luv crib hamptons 3 in 1 crib manual

I was looking for the same thing. My crib has directions on the board that the mattress sits on. It basically says to remove step 4, which is the rail that goes up and down. You slide it up a little from its bottom position and then the screw heads come through the slots that you see and then the whole thing comes off pretty easily. I has to push and pull a little to get the screws through but it worked fine. There is no additional piece that goes on, just stays like that and is stable. My son is very excited to give it a try tonight. Sort of a long way down though! Need to find some extra pillows for a safe landing! Good luck to everyone.

Posted on Apr 24, 2008

  • 2 Answers

SOURCE: Toddler Bed Side rail for Delta Luv 5-in-1 crib

Try calling the customer service number (212)-645-9033. I have not called them yet to get the conversion rails for our Delta Luv 5 in 1, but I'm hoping that they will know more than Babies R Us!!

Posted on Sep 29, 2008

  • 1 Answer

SOURCE: Bed rails for Delta Martine Crib

I have this crib for my own child. I ended up buying a guard rail from Walmart. If you tie a knot in the strap after putting it through the rails and then tuck the disc between the side of the crib and the bottom of it, it seems to work just fine. Child has been using it as a toddler bed for well over a year now and there has never been an issue. Chiild is a restless sleeper too. So, I know it works.

Posted on Apr 07, 2009

  • 5 Answers

SOURCE: Pottery Barn Kids Sleigh Crib broken clip on side rail

We had the same thing happen and Pottery Barn was terrible at helping us remedy the problem. However, after much research, we found the solution! There is a company called Products America (www.productsamerica.com) that sells replacement kits for the PBK cribs. Ours was the antique white sleigh crib...all parts matched perfectly and were identical to the originals! Good luck!

Posted on Jul 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost internal screws while replacing battery. where can I get replacments


Realizing the damage YOU can (and probably will) do by putting the WRONG screw (or bolt) into the VERY WRONG location is EXTREMELY important in ALL REPAIR WORK.

Everything from fender/body DENTS... BROKEN GLASS...
blown out castings on ENGINE BLOCK FAILURES can all be
directly attributed to misplaced bolts...

Let your imagination be your guide...

Knowing that: Your replacement screws are available on AMAZON.

BUT FIRST ... Get an old T-Shirt,

Survey the surface of a respectable area (no holes)...

Stuff it loosely into your vacuum nozzle and run the vacuum over the area of your lost screws...

With luck... the screws might be caught in the fabric inside the nozzle.

Good luck with that... (and yes... I have spent my share of time on that floor with a bright flashlight... (I like playing with watches)).

Nov 28, 2015 | Apple iPhone 4S

1 Answer

Why does the front roller keep dropping, resulting in lawn scalpage?


Is the adjuster broken or wore out so it won't hold where it is suppose too be. Some times you just need to tighten the bolts that holds them on. You may have to replace the adjuster as well.

Jul 27, 2015 | Garden

1 Answer

The fridge door dropped


Probably a loose or lost bolt connected to main body with a pin that supports the door. Usually the fridge has top and bottom pin hinges for adjustment so the bottom one must the problem. Look around for bolt/screw on the ground. If can't find it you will need to buy one to match from hardware (unscrew matching bolt/screw from other side and match). You may need a short handle screwdriver if space is limited or carefully have someone tilt the fridge to get access -MUST place a wood of block under so it doesn't fall squashing your hand when working under . Use small mirror placed underneath to see where the bolt/screw goes. Replace fittings and adjust height of door so it seals.

Feb 16, 2013 | Westinghouse Refrigerators

1 Answer

I need to remove the grill from 98 mazda 626 so I can open the hood


You can't take the grill off because you have to open the hood to get the grill off.Here is a diagram of the latch and cable routing you will have to try to get to the cable from under the car and pull it to open it or use a long screwdriver to unla


REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0900c15280261692.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Exploded view of a typical hood mounting

  1. Open the hood and support it securely. Mark the hinge location on the hood. If so equipped, disconnect the windshield washer hose from its retaining clamp.



0900c15280261693.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Matchmark the position of the hood before removing the retaining bolts


0900c15280261694.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Have an assistant secure the hood, then remove the retaining bolts

  1. Have an assistant hold the hood in the up position. Remove the hood support and remove the hinge-to-hood bolts.
  2. Remove the hood from the vehicle.

To install:
  1. Position the hood against the hinges, using the marks made previously on the hood to help with alignment.
  2. Have an assistant hold the hood. Install the hinge-to-hood bolts, the hood support and the hood support bolts. If so equipped, install the washer hose.
  3. Tighten all bolts securely and check the hood for proper alignment.


ALIGNMENT

Hood
The hood is provided with up-and-down and side-to-side adjustments.

  1. To make the side-to-side adjustments:
    1. Loosen the hood attaching bolts and move the hood to the proper position, then tighten the attaching bolts.
    2. Repeat the procedure if necessary.

  2. To make the up-and-down adjustment (at the rear of the hood):
    1. Loosen the hood stop bolts.
    2. Using a screwdriver, turn the hood stop screws clockwise to lower the hood and counterclockwise to raise the hood. Hood is at the proper height when it is flush with the fenders.
    3. Tighten the hood stop bolts.
    4. Repeat the procedure if necessary.


Hood Latch
See Figure 4
  1. Make sure that the hood is properly aligned.
  2. Remove the hood latch attaching bolts. Move them as necessary to align with the latch dowel. Tighten the attaching bolts.
  3. Remove the locknut on the hood latch dowel, and turn the dowel clockwise to pull the hood tighter and counterclockwise to loosen it. The proper height is when the top of the hood is flush with the fenders.
  4. Tighten the dowel locknut after the proper adjustment has been obtained.



0900c15280261695.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: The hood latch can be adjusted in the directions tch it through the grill.

Jul 01, 2012 | 1998 Mazda 626

1 Answer

I have a nod a way crib i dont have the instuctions can you hellp me so i can putt it together


Nod-a-way cribs go together about the same way as the rest. If you have 2 metal rods
those hold the front-dropdside and allow the dropside to move safely up and down.
The back will have either 4 bolts, 2 on top-2 on bottom or a nub that holds the top side
of the back-fixed rail with 2 bolts on the bottom. The mattress support will either bolt in,
slide into opennings on the head and footboard. The hard thing is getting the dropside
set right so that it drops when you push the release with your foot. Be sure to lift then push
with your foot. Let me know if any of yours is different. I'll try and help more.

Mar 28, 2011 | Childesigns Carrollton Crib

1 Answer

1990 ford escort zx2 torque for the engine head bots


Not sure what engine you have but it's the same for the 1.8L and 1.9L. Hope this helps.. Cobra!!
Installation
CAUTION: Before installing the cylinder head, check the piston squish height as outlined.
  1. Clean all gasket material from the mating surfaces on the cylinder head and block. Clean out the bolt holes in the block.
  1. Install the dowels. Check the dowel height (11.75/10.40). When using replacement parts, a long dowel may be encountered. A long dowel will not allow the cylinder head to sit properly and should not be used.
  1. Position the cylinder head gasket on the cylinder block.
  1. Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown, tighten the attaching bolts to 40-60 Nm (29-44 lb-ft). Loosen all attaching bolts approximately two turns, then retighten the attaching bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence.
6d294e3.gif

Jun 15, 2010 | 1999 Ford Escort

1 Answer

Drivers side seat will not go up or down as designed.


You could remove the seat and check to see if there is anything jammed in the seat rails causing the seat not to adjust up or down. Remove the 4 Torx-40 bolts from the rails tilt the seat back and disconnect the connectors that are lined up under the bottom of the seat. MAKE SURE THE KEY IS OFF AND STAYS OFF. Check the rails, check the operation of the height adjust. If it still does not work then it most likely needs seat rails.

Mar 01, 2009 | 2005 Mini Cooper

4 Answers

Convert to toddler bed


They do have answers on their website, you may want to check your printed or online crib instructions to remind yourself how you put the crib together, too.

I found the answers here:
http://www.pali-design.com/index.php?path=customer_services&template=faq&section=customer_services&subsection=faq&page=faq

i've pasted them below. You can make it a toddler bed without a side rail just by removing the movable side of your crib, and you can install the side rail instead of the movable side if you want it to look a little more finished and help keep your child from rolling out of the bed.

FAQ

How to convert a crib into a toddler bed
To convert a crib into a toddler bed you must loosen the two front gold bolts left and right side of the crib and remove the dropside (the front gate that goes up and down). After removing the dropside be very careful that you tighten back your two gold bolts.

How to install the streight rail (toddler rail)
To install a streight (toddler) rail loosen the two front gold bolts left and right side of the crib and remove the dropside, once you have removed the dropside replace with the streight rail. Always be very careful and make sure you tighten back your two gold bolts in the front.

Oct 14, 2007 | Pali Sabrina Crib

Not finding what you are looking for?
Baby Gear Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Delta Enterprise Baby Gear Experts

Dorel UK
Dorel UK

Level 3 Expert

1629 Answers

yadayada
yadayada

Level 3 Expert

77514 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Delta Enterprise Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...