Question about Computers & Internet

1 Answer

My screen does'nt turn on. - Computers & Internet

Posted by on

  • Theresa  Smith
    Theresa Smith May 11, 2010

    Do you have a desk top or a lap top?

  • Stingrayvt
    Stingrayvt May 11, 2010

    Is it plugged into power, is there a light on the monitor?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sony psp slim

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black screen when turning on


Dr...your windows is nt genuien......its vendor product key is not fake..please re enter a orignal product key..of ur specific product
...Thnk u

Mar 20, 2013 | Compaq Presario CQ56-115DX Laptop

1 Answer

It can't see display so how we go bios. it jumber setting problem i say how to jumber setting in the mother board. but how and where i don'nt know.


o enter the bios Press DELETE or F12 or the key displayted on the screen saying Press key to enter setup. Its the first screen you see when you turn the system on, if you see a logo you can press ESC to go to the display screen with the information..

the JMP is a 3 pin JMP close to the processor. The defaults should be fine, so you dont need to adjust the jmp settings.

Dec 30, 2012 | Computers & Internet

1 Answer

I am turning power on to my Minimax NT but the screen only reads "Off" and will not turn on. I have never had to do anything but turn on my breaker to the unit. Not sure what to do???


1st check the thermistor, it is plugged into the back of the circuit baor on the inside of the door,
It will have either two small white wires ,or it may have two yellow wires.
Pluu the plug from the circuit board, wet your finger and touch the two terminals on the board with the wet finger. IF this doe not work most likely is the circuit board.

Jan 01, 2010 | Pentair Minimax NT Heater

1 Answer

When I turn on the unit it will not read the depth only a blue screen and it will not let me switch out of auto mode or run the sounder test?


I know this is an old question but just ran across it. The 1833C/NT is a radar and chart plotter. It requires the external and optional black box sounder to have depth recorder functionality.

Oct 03, 2009 | Furuno 1833C/NT GPS Receiver

2 Answers

My 480 NT Royal Cash Managment System shows "EE" on the screen and beeps not stop


turn the machine to PRG - unplug for 20 seconds. while pressing clr plug back in

May 25, 2009 | Royal Office Equipment & Supplies

1 Answer

Asus cuv-nt from hp in another puter. boots into xp-n-works fine. However cannot get into bios. has phoenix bios 2.0 tried delete key at start up! any suggestions ? roadtramp


Watch the screen carefully while the system starts after you turn on power. At some point there will be a message telling how to access BIOS setup. It's usually on the manufacturer's splash screen or just after, and disappears pretty fast, so you need to be watching for it. It's not always the delete key. I think F10 works on HPs but it can vary. But there will be a message telling you the magic key.

Mar 26, 2009 | ASUS CUV-NT (CUVNTWOTVWOV) Motherboard

1 Answer

AFTER FLASHING MOBILE DEAD POWER IS`NT ON.


It sounds like you've had problems writing a custom ROM to your phone. You have done it correctly using the CID unlock. Are you using the same WM6 ROM that you have done before?

Firstly, turn off your XDA Orbit.
Then hold down the voice recorder button on the left side of the phone
Then press and hold the power button on the right side of the phone, whilst still holding the voice button on the left.

This should get you into "bootloader mode" which will display a screen with red, green, blue and white stripes - yu should now be able to instlal your ROM using the RRU from the computer with USB connection

If that is not possible, you can install the ROM from a microSD card if you first format the card into Fat32 file system from your computer, then copy the NBH file from your ROM to the microSD card. You will need to rename the NBH file from the ROM to ARTEIMG.NBH for this to work.

Enter bootloader mode and you should see a prompt to press the volume button downwards to start the ROM installation process.

See this page for more information on the MicroSD ROM installation:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing

Nov 09, 2008 | O2 Xda Orbit Smartphone

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

101466 Answers

David Payne
David Payne

Level 3 Expert

14160 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...