Question about NorStar Remote Annex 2000 8-port Bay Enclosure Router

1 Answer

How can i connect to my system to other system. that's why i want to break the firewall that system how can i break that?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 324 Answers

You will need to login to the router's web page to configure ports

Posted on Mar 11, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1993 Ford Explorer where is the vacuum assist break hose

It's connected to the booster assembly off the firewall drivers side. I can provide a diagram if you give me the engine size although the vacuum hose for the brake system is in the same area.

Jul 01, 2016 | Ford Explorer Cars & Trucks

1 Answer

1984 Chevrolet K10, 350. Fan blows warm air but not strong. I don't hear the vacuum motor activate when control is set on MAX. Control is set on MAX and full COLD. Low pressure side is 60psi. ...

There is a single vacuum line that goes threw the firewall that feeds the controls, that will actuate the plenum doors. This tends to break under the hood. If you find the vacuum canister (ball) Make sure it is not cracked first. then follow the vacuum lines and you will find the line that goes into the firewall. Usually a direct connection. Fix it if you find a break. If it broke in the cabin, then it is easier to run a new line than it is to find the break.

Jun 09, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

Which is the break fluid container in front engine? I need to add some break fluid in Dodge 2000

The break fluid goes into the container that sticks straight out of the firewall(the wall that separates you and the engine) Its connected to a big round metal thing that looks like a pan(its called a booster) It should be the only fluid reservoir that is sticking out from the firewall.

Mar 09, 2011 | 2000 Dodge Caravan

1 Answer

Break system boster . the part thats connected to the peadle has seal that is broken. i need to know the name of the part and how to replace it.

The name is exactly that "Brake Booster" To remove it: Remove the master cylinder assembly and vacuum hoses from the booster. On the interior side of the firewall you will have to unbolt the booster and disconnect the linkage attaching the pedal to the piston in the booster.

Feb 25, 2011 | 1994 Dodge Intrepid

2 Answers

Can't change from defrost to dash vents. I think it is a vacuum problem.

Ther vacuum control line is leaking. This usually occur very close to the 3 way junction. Check on the passenger side under the hood,for a small RED plastic hose, that connects between the connection on the firewall and the rubber junction.

The break is usually in this RED tube.

It is usually glued in place, but can be separated with a little elbow grease.

If you disconnect and examine it close to the end, you will see the break usually wher it bends.

It is usually safe to cut it wher it break and reconnect it, and it should work fine after.
WARNING!! Before you do any repairs on this car you should first disconnect the negative ground.
Otherwise the computer may not recognize the repairs for a while after.

Mar 11, 2010 | 1998 Ford Windstar

1 Answer

Forgoten en mode password, want to flatten firewall and re configure

No need to flatten the configuration and reconfigure:

Once you use this, you can reset the password to anything you want. Please keep in mind you have to physically power down the unit, connect a console, then power up. Then hit "Break" within your terminal program and follow the instructions. Pretty simple, actually.

Good luck!

Jan 27, 2010 | Cisco ASA 5510 Firewall

1 Answer

Problem with firewall rules and access from WAN

  • call your router support to disable first the firewall on the WAN setup
  • the do port forwarding

Aug 10, 2009 | Trendware TEW-432BRP 54Mbps Wireless...

1 Answer

How to disable firewall connections on an HP

Hi there,

As its HP im guessing you will have Nortons Anti Virus Running On The System, If You Left Click This For A Minute And Press Disable That Should Disable Your Firewall.

Also have you tryed to run itunes, as once that is installed your firewall should let you gain access to the Ipod

Feb 16, 2009 | HP Pavilion A1130N Athlon 64 3500+ DVD+RW...

1 Answer

FTP problems.

There are 2 ports used for FTP. They are 20 and 21. When you initiate a connection that occurs on port 21, but data traffic is on port 20. Your firewall sees your outside FTP server trying to 'initiate' a connection on port 20 and breaks the connection to that IP address.
What you need to do is either use 'passive' ftp or open both ports 20 and 21 for ftp traffic in the firewall.

Apr 02, 2008 | D-Link DFL-800 Firewall

Not finding what you are looking for?
NorStar Remote Annex 2000 8-port Bay Enclosure Router Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top NorStar Computers & Internet Experts

Brad Brown

Level 3 Expert

16162 Answers

Computer Links

Level 3 Expert

2385 Answers

 Brian Main
Brian Main

Level 3 Expert

464 Answers

Are you a NorStar Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides