Question about Ruud UBHC Air Conditioner

1 Answer

RUUD (Protech Model 500) Thermostat Single Stage Not Programable

The thermostat LED shows the heat is suppose to be running (little fan rotating in the lower left hand corner). However it is not. I have to keep turning the thermostat off and back to heat in order for the heat to come on. When it comes on, runs for a few minutes and shuts down before reaching the set temp. I have changed the batteries and still the same problem. Anyone help with this problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Problem is not the thermostat, thermostat is an on-off switch that happens to work on temperature. Your furnace is locking out. cycling the heat off switch resets the micro-processor in the furnace. You need to diagnose the problem in the furnace, to go further we will need the model and approximate age of the unit

Posted on Dec 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Rheem Classic Super Quiet 80 gas furnace (for heat). The fan stops when the "heat" turns on.


Any time I ever had trouble,first thing to suspect is the thermostat.
They lose contact sometimes and sometimes you tap the face and they work til next glitch.
If the thermostat has some years on it,go ahead and replace it.
Can't you just leave the heat and fan in auto? That would be best,I think. don-ohio

Jan 10, 2017 | Heating & Cooling

1 Answer

Where are the batteries on my thermostat


If you posted the Brand and model that would really help. Sometimes they are in the front behind a little door or more commonly you need to take the thermostat off the sub base and they are on the back of the thermostat.

Jan 10, 2017 | Heating & Cooling

1 Answer

My Coleman furnace 4322/729 model lights the pilot but won't cut in . What could be problem ? Cleared lines Complete


Gas valve not opening? Does it have the exhaust blower that pulls vacuum switch allowing burner to light?
(1) Thermostat not working? Has to complete the circuit in or gas valve to open.
(2)Can be a stuck or bad gas valve. Try tapping the side of the gas valve body while thermostat is calling for heat. Tapping,not pounding. Like lightly,yannow? don-ohio (:^)

Jan 03, 2017 | Coleman Heating & Cooling

1 Answer

We have royal red furnace to heat our home.The fan dose not stop.


Details.......does the furnace function normally otherwise? Might just be a stuck fan switch. Make sure the thermostat hasn't been set on Fan ON setting or summer air circ. on older furnaces.
Find the fan switch and tap it and see if fan quits. If it does,fan switch is bad.probably. Always make sure your air circ. filter(return air to furnace) is replaced every 3 mo. or so,too. don-ohio (:^)

Jan 03, 2017 | Royal Heating & Cooling

2 Answers

My thermostat is set on 68 degrees and it shows room temperature is 68, but the furnace still kickson, Honeywell said it has a 1 degree difference. so what's the problem then?


Yes there is a one degree tolerance, in fact my heater just kicked on and it is set to 67 and the inside temperature reads 67. It is also a Honeywell.

Dec 28, 2016 | Heating & Cooling

1 Answer

My termost set to a/c, the fan auto, blow very well, but when I switch to heat and the fan auto, doesn't work, but if I put fan on work why?


the thermostat says to call for heat buildup in the work if its not cold enough the thermostat won't call for heat and I won't go on but when it gets cold and the thermostat set to the temperature you want or hire someone that doesn't cycle

Oct 12, 2014 | Heating & Cooling

1 Answer

I have a Coleman Evcon electric furnace, the blower fan runs constantly and I have to shut the breaker off inside the front cover to turn it off. The switch is on auto and it runs even when the thermostat...


It could be a thermostat problem. Also it will seem to run constantly as it tries to heat and one of the elements are working which could be a sequencer problem.

Nov 28, 2013 | Heating & Cooling

2 Answers

A/c fan not working=thermostat is working(central a/c system)a/c


The fan on the outside unit is powered from it's 240 volt source. Check that the breaker for the outside unit is not tripped. Also, a contactor is inside the outer unit that starts the fan - it may be faulty.

Jul 26, 2008 | Friedrich QuietMaster Electronic SS12J30D...

Not finding what you are looking for?
Ruud UBHC Air Conditioner Logo

2,012 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ruud Heating & Cooling Experts

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Are you a Ruud Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...