Question about Dell (E210882) Motherboard

1 Answer

Dell Dimension E310 not booting

When I press the power button there is a beeping sound and then 3 & 4 on the front panel is illuminated.

Posted by on

  • d_brat81 Dec 11, 2008

    Thank you will try and let you know how it goes!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

Unplug Motherboard completely from all power. Remove RAM and all ISA/PCI/PCI-E/AGP cards out carefully and wait like 5 minutes. Try again using only bare essentials: Video card and 1 stick of ram. Alternate RAM is possible if it doesn't work. Try a New Video Card if nothing else works... Most MB manufacturers will have a chart that has the beep codes so you can at least narrow it down if not solve it by the beeps.

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Del 320 optiplex orange lite blinks won't boot up



For the Optiplex 320, a flashing amber light with no sound indication can mean 3 things.


1) Your power supply has failed

2) Your motherboard failed, most likely from a bad capacitor.

3) The front panel board (where the power button is located) is faulty or not connected properly.


I've worked with 10's of 1000's of Dell Optiplex's over the past 8 years and the flashing amber light is well known as a tell-tail sign of one of those three failure. Always start your trouble shoot with a PSU tester, then inspect the motherboard for domed or split/leaking capacitors...then on to the front panel which would require another panel and ribbon from the same model.

Jan 25, 2014 | Dell Optiplex GX280 (99301) Motherboard

1 Answer

D845GVAD2 no bios screen no beep no boot


Hello here is the intel homepage:

https://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Desktop+Boards&ProductLine=Intel%C2%AE+845+Chipset+Family+Boards&ProductProduct=Intel%C2%AE+Desktop+Board+D845GVAD2

Try to renew the power supply, with one you know is working.
I think that`s the problem.

The problem could ofcourse also be the mainboard itselves failing.
There is not much to do about that, other than renew the mainboard or buy a new pc.

Good luck

Apr 08, 2013 | Intel D845GVSR Motherboard

1 Answer

K0057 boot issue


When you plug in the power cord is there any lightswhatsoever on the laptop, where the plug goes in or on the AC Adapter of thepower cord?

When you press the power button do you hear fans running, hard drive spinning,lights on the computer, hear any beeps or lights constantly blinking, hear theDvD/CD drive click and the light on the drawer of the DvD/CD turn on for asecond or two? If so the laptop is trying to boot or may have booted, butthe screen is not showing for some reason.

Beep tones and blinking lights tells the technicians what is going on with thelaptop and why it is not booting. Most times it's a motherboard issuewhen you hear beeps or blinking lights continuous. Most times the problemis with the memory or Video Card. Count the Blinking Lights or Beeps and takenote of their pattern (1 Long or 1 Long followed by 2 Short).

Maybe your power cord is bad if you don't get anything to happen whatsoeverwhen you press the power button. And if that's true maybe you wasoperating off the battery the last time you had it on and since the power cordis bad, it was not charging the battery so the battery is drained and the powercord is bad.

Maybe you have a Static Charge Buildup. Remove the Power Cord, Remove theBattery, then Press and Hold the power button for 30seconds. After 30 seconds plug the power cord back in (leave the batteryout) and hit the power button to see if it boots. If it does, you can putthe battery back in and let it charge.Maybe your DC Power Jack which is where the power cord plugsinto the computer is bad. Take an ink pen and push the tip inside thejack and see if the little pin wiggles, if so the jack is bad. You'll have totake the laptop apart to fix it. Most times it is soldered onto themotherboard, so you will have to desolder the old and solder a new one.Maybe your memory is bad or the memory slot is bad.Remove the Power Cord, Open the Case and remove one of thememory chips. Set the chip aside then try rebooting the computer. If it boots, then you know the memory chip you set aside is bad so mark an x onit with an ink pen. If it fails to boot then move the chip to the nextmemory slot and try rebooting. If it fails take the chip out and set itaside, then put the other chip in and try booting it in both slots. If itboots, just to verify that the chip set aside is bad, mark an x on it and putit into the open memory chip slot and try booting.

May 30, 2012 | Genuine Dell K0057 Dimension 2400c...

2 Answers

Problem with panel front conector in Dell Dimension 2200 motherbo


The following information is to assist you in performing the right connections. You should take precautionary measures such as grounding yourself and completely disconnecting the PC form any source of power.

This picture shows the connector for the front panel power button, reset button, and power and hard disk lights: an 8x2 pin connector with 1 pin missing:



0505a76.jpg
The table below lists the pinouts for the connector. The orientation of this table is the same as the picture above, this shows the top part of the connector. All the pins below pin 8 appear to be non-connected.


f07048e.jpg


Each pair of pins labeled Power and Reset goes to the 2 wires for the corresponding button. The hard disk and power LED wires connect to the corresponding LEDs, you need to ensure the proper polarity of the + and - wires for each LED or it will not illuminate.

The above information is for your information only.

Mar 01, 2010 | Dell (2M502) Motherboard

2 Answers

Can't turn my compuer on


Check on *********** board that your CMOS jumper is in normal mode otherwise change it - also check any beep sound aswell as you remove all the cables ie.. IDE cables, front panel cables I mean only the 2 power cables to the motherboard and try to start the pc by shorting the power switch pin with a screwdriver see the display coming or not ????

IF it is a branded pc - you have to buy the same companies motherboard, normal motherboard will not work with branded pcs.

Sep 27, 2008 | Dell (S423) for Dimension 8100 (3F546)...

1 Answer

Dell dimension 5150 - start up


you may be knowing there are many types of beeps which made as standard for all pc ...
if the pc beeps for 30 seconds and then starts means there is no input device connected ...(here the standard input device is keyboard)
so c the keyboard is connected properly or not try reconnecting it...
and about the display when sometimes computer makes beeping sound the screen is not displayed ... after connecting that just try is it working or not.. if problem persists then just check the cables of the monitor too... try reconnecting them also.....

Feb 11, 2008 | Dell (002TR) Motherboard

1 Answer

Dell Deminsion E310 will not boot


NTOSKRNL.EXE is missing or corrupt. To restore the original boot.ini file in Microsoft Windows NT or Windows 2000 you will need an ERD and follow the below steps.

Good Luck, Please dont for get to Vote/Thank You.

Dec 20, 2007 | Dell (E210882) Motherboard

1 Answer

Dimension 8100 Power on reset


go back to where you did this ... "after leaving the power on for some time (>30 min.) I tried un plugging the AC cord and immediately plugged it in and got POST and BIOS setup and a good bood to a known good hard drive. Left it on for 3 days running AutoCAD, ran reliably."... do that again, but this time, leave the pc on and turn it off using the hibernate feature (must enable it first) as a test of potential faults.

Sep 20, 2007 | Dell (S423) for Dimension 8100 (3F546)...

Not finding what you are looking for?
Dell (E210882) Motherboard Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18330 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...