Question about Goodman GMS90703BXA Heater

2 Answers

The insulation used in the blower fan cabinet has fallen off

I have a GMS90904CXA Goodman heater in my attic space. It's a leftsided mounted install. The insulation in the blower fan cabinet has fallen off the cabinet wall. I would like to know what type adhesive should or can I use to reattach it. The insulation has the old adhesive dried up on it. I was thinking of using a heavy duty construction adhesive called "Liquid Nails" I was concern if it would hold up to the heat, if it was flamable, and would it adhere to the old adhesive. Thanks for your help

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,420 Answers

Use a silicon based adhesive. It will withstand higher heat.

Posted on Feb 20, 2009

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

Get a good can of spray adhesive and follow the directions on can....can get at most hardware stores! good luck!

Posted on Dec 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a goodman gms90904cxa gas furnace in the attic. the inducer motor starts and stops continuously which delays the start of the burners. Any ideas.


put a voltage meter across the leads of the draft motor checking to see of the supply voltage is intermittent also. If it is check the wiring for shorts. If none found then change the board.

Mar 01, 2015 | Goodman Heating & Cooling

1 Answer

I turn the thermastat to heat on my goodman gms90904cxa and the inducer fan does not come on and after a couple of seconds the lights blink 3 times


Hello, a 3 blink pattern indicates a open limit switch. Most of the time a dirty filter, dirty blower wheel, weak blower motor, can cause the limit switch to open.

Oct 02, 2011 | Goodman Heating & Cooling

1 Answer

The goodman air conditioning unit will randomly turn on and run for a few minites then turn off. The blower fan does not run just the unit in the attic. Any advice?


Hi, not enough detail not enough detail. I have no idea where you are located, but if it is a gas heater/ Ac then maybe the attic space is so hot that the over temperature sensor is turning the unit on in an attempt to cool the system down. If however it is a refrigerant AC unit, I would suggest that the control circuit is faulty, maybe a sticking contact somewhere. good hunting col

Feb 24, 2011 | Heating & Cooling

1 Answer

I have a Goodman GMPN furnace and the motor that runs the twin blowers has quit. How do I take it out and replace it?


If you mean the blower wheel, I wonder how you diagnosed this problem so you were 100% sure the motor is bad. I recommend to make sure of the diagnosis before spending to buy parts.

The blower wheel is shaped like a twin blade. But it's only one wheel.

However, to answer the question; Step one is turn the power off.
Then; Find the blower housing in the lower compartment on an upflow configuration.
  • Remove 2 screws on the blower housing, on the upper inside of the blower compartment to slide the blower housing out.
  • Disconnect blower motor wiring at the harness and at the control board if connected. You can cut them if you have exact replacement motor and wire nuts.
  • Slide the housing out, turning it on the side that exposes the motor.
  • Remove the 3 mounting screws holding the motor to the housing.
  • Loosen the lock nut holding the fan blade (wheel) to motor shaft.
  • Slide motor and shaft out and away from the fan blade, as they are connected together and cannot be separated. Use penetrating oil SPARINGLY.
Installation is the reverse of the removal instructions.

IMPORTANT. Make sure to leave equal space between both sides of fan blade and housing when re-installing the wheel.

Luck to you. Let me know how that turns out.
Russ
myairfixer@gmail.com

Dec 23, 2010 | Goodman GMS90703BXA Heater

1 Answer

Insulation stinks took out how do i get replacement


The easies solution is to use 1/2" duct board with the foil side towards the blower. Put it on with a HEAVY coating of spray adhesive on both the duct board and the surface you are mounting it to.

Call around to the wholesalers to find ductboard in your area.

Jun 16, 2010 | Goodman GMS90703BXA Heater

1 Answer

GMS90904CXA IR Blower continues to run after it


it sounds like the fan control switch is not shuutting off when it cools down look at the fan diff settingson the fan control you may be able to adjust this

Feb 03, 2010 | Goodman GMS90703BXA Heater

1 Answer

Furnace gms90904cxa I have 3 blinks what s the


Pressure switch is not working, plugged air intake or exhaust pipe, dirty air filter, debris in condensate hoses, debris in pressure switch hose.

Oct 18, 2009 | Goodman GMS90703BXA Heater

1 Answer

I have a Goodman Heater model number GMS90904CXA and the fan is making a loud noise. I'd like to replace the fan and motor but don't know model # of the motor and fan???


The motor will have a horsepower and rpm on it. pull it out and take down to a local parts warehouse they will have a replacement

Jan 05, 2009 | Ingram GMS90904CXA Heater

1 Answer

Blower fan


you could use only 2 wires, R and G terms all you would get is blower fan. so on stat make sure you connect to R and G also. also did it have a fresh air return and you miss hooking up those wires, i have seen that before.

Dec 15, 2008 | Goodman GMS90703BXA Heater

Not finding what you are looking for?
Goodman GMS90703BXA Heater Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

paulcarew

Level 3 Expert

2398 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Goodman Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...