Question about Telex FMR-200H Professional Microphone

1 Answer

Telex prostar wireless mic.  leads came off of mic element.  One green wire and one black.  Which one connects to center of element and which connects to rim.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,175 Answers

Hi..
The rim is "ground" or the (-) side of the mic.
Find out which wire goes to ground or a (-) on a battery.
Solder that one back to the rim

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Telex HT-100 with TE-10 head pulled off


724ad609-7aa4-403c-beb1-0ee8eacb80d3.jpg
I realize that this question was asked in December of 2011, but I just now found this question on this website today.

Here's a picture that I took of the Telex HT-100 wireless microphone transmitter that I have showing the wiring on the circuit board.

The green wire gets soldered to the lead of the 10 Megohm resistor that you can see in the picture.

Dec 28, 2011 | Telex Microphones

1 Answer

Telex ht200 is fatter microphone and I am looking for a microphone clip to mount it on a microphone stand. Universal clips are too skinny - they will not fit around the mic. Does anyone know where I cn get...


Here you go. I would use something like this. This has a 1.75" (44mm) diameter. http://www.bhphotovideo.com/c/product/298898-REG/WindTech_MC_4_MC4_Extra_Large_Heavy_Duty_Microphone.html
You can also go here http://www.crossroadsaudio.com/Rentals%20Catalog.pdf scroll down to page 5 and you can use this - $15.00 Telex ELM-22S Black Lapel Mic, Shure TA4F w/ Mic Clip -- That clip is the same diameter as your mic and is made by Telex.

Mar 22, 2011 | Telex HT-200 Handheld Microphone...

1 Answer

How do I order a mic clip for the wireless mic. The one I have broke.


Contact Bosch/EV (formerly Telex) via website or call them. They're in Burnsville Minnesota and their customer service is excellent.

Feb 25, 2011 | Telex WT-55 Belt Pack Transmitter (027)...

1 Answer

ProStar UB12. When I turn on the wireless, I get occasional static that is irritating to the point I cannot use it. Is there a fix?


I had the same problem. Mostly, when using near energy saving fluorescent lighting. I would receive high static, especially when the mic was off. We were using it indoors & usually no more than 200 ft from the receiver. I opened it up, resoldered some poor solder connections, sprayed contact cleaner on the squelch & volume controls, but still had the problem. What actually resolved the issue, was turning the squelch control (thru back panel) fully clockwise & completly lowering the antennas aimed horizontally to the rear. If you are using it outdoors, you should not have interference from fluorescent lighting, but may need to raise the antennas if operating from a greater distance.

Sep 16, 2010 | Telex FMR-200H Professional Microphone

1 Answer

I have an old Telex Prostar R-10 Series 2 wireless mic without a power supply. i could really use this tomorrow. could i get the power supply specs so that i could get help at radio shack? thank you, Randy...


Hi Randy,

If you take the receiver with you, Radioshack can absolute help you to get the right power supply with the right connector.

Regards,
Gerard

Feb 04, 2010 | Microphones

1 Answer

Where in the circuit is Mic On/Off switch located? In other words, what components are between the mic and the Mic switch?


The switch is between the Mic element and the output connector.
Depending on the type of microphone will determin how the switch is wired.

Jan 15, 2010 | Telex WT-55 Belt Pack Transmitter (066)...

1 Answer

Telex 56 to cobra 4 pin


Hi there!!

the yellw wire is not used on the microphone conector most of them are just cut and left in there loose as long as its not shorting out on anything!! The wiring for the telex 56 for your radio Cobra 29 LTD is as follows: PIN #1 Shield & Red, PIN #2 White, PIN #3 Blue, PIN #4 Black, Yellow wire not connected!!

If you notice when you have the connector apart on the back of the pins where the wires get soldered to the pins are numbered so you will know which pins they are or on the front side of the connector the pins are also marked wich numbers they are!! If you have any other questions please feel free to e-mail us at: bigdscbshop@hughes.net

Apr 18, 2009 | Telex M-560 Consumer Microphone

1 Answer

Telex WT55 wireless lapel mic & FRM70 Receiver


How do I set the squelch on a TELEX FMR-70 receiver?

Jan 27, 2009 | Telex FMR70 VHF Wireless Microphone...

1 Answer

Telex ProStar VR12 VHF needs repair


I've been in contact with Telex and although the Prostar is obsolete they still maintain some repair parts. I would contact them:

http://www.telex.com/Support/

Jan 07, 2009 | Telex FMR-200H Professional Microphone

1 Answer

Telex M-560


may be mic preamp is not working correctely. condenser microphone voltage is very low or mic is fault . check your microphone cable . preamplifer of condenser mic may be leaking .check ur mic driver and audio .

Feb 22, 2008 | Telex M-560 Consumer Microphone

Not finding what you are looking for?
Telex FMR-200H Professional Microphone Logo

Related Topics:

568 people viewed this question

Ask a Question

Usually answered in minutes!

Top Telex Microphones Experts

Rick

Level 2 Expert

611 Answers

Iron
Iron

Level 3 Expert

3018 Answers

GERHARDUS STROEBEL

Level 2 Expert

76 Answers

Are you a Telex Microphone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...