Question about Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite washer model 20952992 pouring water

Every time I wash clothes no matter how small the load my Kenmore Elite washer model #20952992 pours water out of the bottom. Facing the machine, it appears to be coming out of the front right corner.

Posted by on

  • rdricosuave Jan 03, 2009

    water comes out during draing of tub. front of machine.

  • hhkllc Jan 24, 2009

    I have the same exact problem.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

We had the same problem. The bleach dispenser tray is located on the drum below the bleach storage pan. The dispenser tray has very small holes that were plugged by rust from the hose clamp that attached the dilution water supply hose to the bleach storage pan. I removed the top of the washing machine to discover the problem, but it may be solved by attaching a flexible tube or small hose to the end of a vacuum cleaner hose and cleaning out the dispenser tray. There is room between the dispenser tray and the storage pan and is located in the front right corner.

Posted on May 14, 2009

  • johnjoakim Jul 19, 2011

    The dispenser tray has a row of holes for draining, but where is it supposed nto darin to? Ours seems to end up on the floor. Should there be a hose attached to the underside of the drain tray, and where should it drain to??

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenmore elite he3 smart heat quiet pak4 how much is a motor for this dryer


  1. Kenmore Elite He3 Parts - searspartsdirect.com‎

    Adwww.searspartsdirect.com/Kenmore-Parts‎rating for searspartsdirect.com
    Shop Today at Sears PartsDirect™. The Largest Appliance Parts Seller.
    Ratings:Shipping 9/10 - Website 9/10 - Selection 9/10 - Quality 9/10
Search Results

    MOTOR diagram for model # 41794130000 Kenmore-elite ...

    www.searspartsdirect.com/model-part/41794130000/0583/.../00004.html
    MOTOR Diagram and Parts List for KENMORE ELITE Dryer-Parts model # ... MOTORdiagram for model # 41794130000 Kenmore-elite-Parts Dryer-Parts (18).

    PUMP AND MOTOR PARTS Diagram & Parts List for Model ...

    www.searspartsdirect.com/model-part/11047789702/0583/.../00006.html
    PUMP AND MOTOR PARTS Diagram and Parts List for KENMORE ELITE ... ANDMOTOR PARTS diagram for model # 11047789702 Kenmore-elite-Parts ...

Nov 01, 2015 | Kenmore Dryers

3 Answers

Kenmore Oasis Elite Washing Machine


dont overload machine and use fabric conditioner

Aug 18, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

I have the Kenmore Elite Gas Dryer (not steam). I


Take pantyhose around the inside and see if it catches.
Pay particular attention around the drum/door area.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 11, 2010 | Kenmore Elite HE3 Steam 8674 Dryer

1 Answer

Kenmore Elite HE4 won't start


Top 10 front-load washer problems

1)Water fill problem: water took more than 10 minutes to fill to desired level sometimes indicated as a LF/IE or long fill/inlet error. Water valve screens clogged, hoses kinked, low water pressure, unpaid water bill. Check hose, clean screens.
2)Excessive vibration: noisy,roar, knocking noises. Bad damper,bearing or broken trunnion. no error code
3)Dispenser drawer open/detergent in wrong compartment: washer will not operate with drawer open or cleaning products in wrong compartment.
4)Washer won't drain: clogged pump/filter, slow or clogged drain usually indicated as a LD/DE, if a code is given (long drain/drain error) Clear pump of objects
5)Drum overfilled: usually caused by sediment in the water level pressure sensing tube going up to the main control.Find it and blow out the sediment, re-secure pump out water and retry.
6)Door open, Door not latched, clothes/objects keeping door from completely closing. Tighten door latch, add washers if nesessary to make good contact and close door tighter in case of leaks.Note some models send a signal to the motor and another to the control letting both know the door is secure before proceeding, corrosion gets into the lid lock and the door can be locked and the control is ready but the motor ain't getting the message.
7)Cold water does not enter washer: hoses connected backwards. Oops.
8)Over-sudsing: Wrong Detergent, too much detergent, detergent in wrong dispensing drawer, turbidity monitors pick up particles in the water and judge soil content then the washer allows for extra time to wash the clothes, if the wrong detergent is in there the machine thinks that is too much and declares a suds error. On some models a suds detect is determined by the motor over amping, most machines will try a few mini loads to correct the problem. Remove detergent, retry
9)Locked motor: error LE,loose connection,broken wire/hallsensor, motor overheated/failed.
10)Water heating error, hE, the thermister/heater is out.

Feb 06, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Elite He3 dryer..fine on timed but leaves cloths wet auto


find the metal sensors in the drum
scratchem up with sand paper

especially if you wash rugs, sneakers , or anything with acyrlic

Oct 05, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

I have a kenmore elite HE3 t and latley after it's


You could have a clog in the housing underneath the dispenser where the water flows through a hose into the tub.
Pull the dispenser drawer completely out.
There is a tab that needs to be depressed to release the drawer and remove it.
Check the opening at the bottom of the housing just inside the dispenser housing opening to see if a small sock or garment is clogging this opening.
Reach down into this opening to see if an item is inside the hose.
This is the normal issue that will cause water to leak out of the dispenser housing.

Wash the dispenser drawer thoroughly with warm water. Make sure that you pull off the siphon covers and wash all siphon holes. This process is described in your owner's manual. Replace the dispenser drawer and try the washer again.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Oct 04, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite washer problem


LD stands for long drain, you probably have a bad pump or the pump is clogged with lint etc.

Jan 15, 2009 | Kenmore Elite HE4 Electric Dryer

5 Answers

Kenmore Elite Calypso washer won't fill with water!


i assume that the warer is turn on at the warer valves if so then do you have voltage at the water valve if not then water pressure switch could be bad or main control board could be bad

Apr 24, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore elite canyon capacity top load washer


check lid switch make sure its makeing contact right should hear it click

Sep 02, 2007 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...