Question about AEG L66600 Front Load Washer

Open Question

Aeg l66600 error code e60 what problem

Aeg washing machine

Posted by on

4 Suggested Answers

  • 4 Answers

SOURCE: error code e60

Hi I had this on my zanussi not long ago I pressed the reset button in for 5 seconds and it stopped . The computer board needed resetting. Hope this helps

Posted on Jul 08, 2008

  • 1 Answer

SOURCE: Anti-flooding system has activated.

Tip washing machine towards you, water in bottom of machine will pour out, so be ready! Should work after that, mine did!

Posted on Nov 18, 2009

  • 174 Answers

SOURCE: What does error code c9 mean?

c9 means there is no motor movement, typically worn out motor carbon brushes.

Posted on Jul 16, 2010

  • 430 Answers

SOURCE: AEG washing machine error code

E40 relates to the door being left open when the programme is started, it maybe that the latch was not pushed over when the door was shut.After the door is closed again the fault should go away. If it does not and you hear alot of clicking from the door lock you may just have a door lock at fault.Code E40 is door not closed, could be a mis-aligned door or faulty door switch.-------------But if door is closing properly and you are confirmed that door is getting properly locked, then other possibility can be gunked filter or blocked drain pump.It requires cleaning internally.The procedure is as follows:--- Towards the bottom right of the machine is a pull-down flap.
Drain the machine - there's a tube at the bottom of the machine
with a plastic plug - you'll see a butterfly handle, pull hard; the plug
is a round ball on the end of a stick.
Unscrew the large diameter thing (pump cover) -
Don't do this before the drain step!!!
Withdraw the filter cylinder and remove any gunge - the
filter port has two ports - the left one is the impellor
pump and the right one is the discharge pipe; feel to ensure
these are not gunged up either.
Reassemble in reverse order - as Haynes say.
Almost every programme necessitates a pump activation to
assure that the machine is empty of water .-----------

Posted on Apr 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Supra washing machine E60 error


E60
Washing machine motor does not work - no drum action or rotation or not spinning
  • Check motor wiring
  • Check motor
  • Check electronic controller
http://www.ukwhitegoods.co.uk/help/fault-codes/laundry-fault-codes/3337-zanussi-zwg-range-washing-machine-error-codes

May 03, 2016 | Supra Washing Machines

1 Answer

E60 Error Code on converted 60Hz outlet


Hi,

E60- Fault in washing NTC sensor
-Washing NTC sensor, wiring, main PCB

Unplug your washer for 1 hour and then plug it back.See if this reset helps.

Aug 06, 2008 | AEG L74800 Front Load Washer

1 Answer

My aeg lavamat 41070 washing machine doesn`t work at high temperature ( more then 50 degrees) . At low temps it is working OK/


In the case of insufficient heating appears error code E60 what means replace the NTC sensor. Exclude heater, PCB or relay malfunction because you indicate that the machine is heated to 50 degrees Celsius.

Dado

Feb 28, 2015 | AEG Washing Machines

1 Answer

E60 code on Aeg lavertherm dryer understand it us


Yes the NTC or thermal cutoff failure can cause E60 error.

It may look something like this.
AEG Thermostat Thermal Limiter

For diagrams of your dryer refer this site.
AEG LAVATHERM 60750225500 Tumble Dryer Thermostat Spares Parts

Sep 20, 2014 | Dryers

2 Answers

My AEG Lavamat 66600 Washing Machine is showing E60 Message how can I remove it to get the machine working again. Thank you


Please remove the power plug and depress all the buttons on the panel, while the power plug is inserted and power switched on , press on the start/pause/stop. it must restart the controller unit or there can be external or internal errors as designated by E60.
Check the door switch,drain pump and inlet flow.

Jul 25, 2012 | AEG Washing Machines

1 Answer

My AEG Lavamat 62810 keeps coming up with an error code E60. What is this?


On my AEG Lavamat 62810, when I turn on a wash cycle a motor (pump?) runs for 10–20 seconds then the machine switches off, with no error message. When this happened a few weeks agao running a drain cycle seemed to cure it; now the same thing happens on spin/drain/rinse cycles too. Any ideas?

Aug 06, 2010 | AEG Washing Machines

1 Answer

Error code e60


Hi I had this on my zanussi not long ago I pressed the reset button in for 5 seconds and it stopped . The computer board needed resetting. Hope this helps

Jul 07, 2008 | Zanussi ZWF1440 Front Load Washer

3 Answers

AEG OKO LAVAMAT 86741 UPDATE. WASHING MACHINE


I have washing machine AEG 62800 model.
When I tried to start a washing the error E60 was displayed on screen.
The following actions were done:
1. Turning knob to right to first position "COTTON LINES 95"
2. Pressing on all 5 functions except START button (Rinse Hold, Rinse+, Time Saver, Pre Wash, Stain).
Red lights will flash .
3. Pressing on Start button and simultaneously starting to turn clockwise till OFF position.
It will reset error and will release machine.

I'm hoping it will help.

Boris.

Feb 25, 2008 | Washing Machines

1 Answer

Error code 50


i think you should pull out the filter, and clean it. appliance doctor

Jan 23, 2007 | AEG L66600 Front Load Washer

Not finding what you are looking for?
AEG L66600 Front Load Washer Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1450 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...